Publicidad
Idiomas disponibles
Idiomas disponibles
SAFETY AND GENERAL INFORMATION
Save these instructions. For your safety, read, understand, and follow the information provided with and on this
device before using. The owner and/or operator shall have an understanding of the device, its operating characteristics
and safety operating instructions before operating the equipment. The owner and/or operator shall be aware that use
and repair of this product may require special skills and knowledge. Instructions and safety information shall be read
to and discussed with the operator in the operator's native language, making sure that the operator comprehends
their contents, before use of this equipment is authorized. If any doubt exists as to the safe and proper use of this
device, remove from service immediately.
Inspect before each use. Do not use if abnormal conditions such as cracked welds, damaged, loose or missing
parts are noted. Any equipment that appears damaged in any way, is found to be worn, or operates abnormally shall
be removed from service until repaired. If the equipment has been or is suspected to have been subjected to an
abnormal load or shock, immediately discontinue use until inspected by a factory authorized repair facility (contact
distributor or manufacturer for list of authorized repair facilities). It is recommended that an annual inspection be
made by an authorized repair facility. Labels and Operator's Manuals are available from the manufacturer.
PRODUCT DESCRIPTION
This Hydraulic Service Jack is designed to lift, but not support, one end of a vehicle. Immediately after lifting, loads
must be supported by a pair of appropriately rated jack stands. This MagicLift™ service jack has a unique feature
that provides fast, no load lifts to the jacking point, at which time it lifts in approximately 1/4" ~ 3/4" increments.
!
WARNING: Never use a hydraulic jack as a stand-alone device. After lifting, immediately support the lifted
vehicle with a pair of appropriately rated jack stands.
SPECIFICATIONS
Model
Capacity
Jack Dimensions (L x W x H)
GQ035
3-1/2 Ton
30-7/8" x 14-7/8" x 7-1/4"
!
WARNING
• Study, understand, and follow all instructions
before operating this device.
• Do not exceed rated capacity.
• Use only on hard, level surface capable of
supporting the load.
• Lifting device only. Immediately after lifting,
support the vehicle with appropriate means.
• Do not move or dolly the vehicle while on the
jack.
• Lift only on areas of the vehicle as specified by
the vehicle manufacturer.
• No alterations shall be made to this product.
• Failure to heed these markings may result in
personal injury and/or property damage.
Min. Height
Max. Height
Saddle Dia.
4"
21-5/8"
4-3/4"
!
WARNING
To avoid crushing and related injuries:
• Never work on, under or around a load supported
only by hydraulic jack.
• Always use a pair of adequately rated jack stands.
• Chock each unlifted tire in both directions.
• Do not use this device to lift, level, lower, support nor
move a house, mobile home, travel trailer, camper
or any building structure.
• Be alert and sober when using this product. Do not
operate under the influence of drugs or alcohol.
2
PREPARATION
Assembly
1. For Model GQ035, assemble the 2-piece handle with provided bolt.
2. Insert handle into the handle fork. Tighten the bolt on handle fork to prevent accidental removal of handle while
in use.
WARNING: Do not lift or carry jack by handle. Handle could dislodge and jack fall, resulting in possible injury
!
or property damage.
Before Use
1. Verify that the product and application are compatible, if in doubt call Omega Tech Service (888) 332-6419.
2. Before using this product, read the operator's manual completely and familiarize yourself thoroughly with the
product, its components and recognize the hazards associated with its use.
3. To familiarize yourself with basic operation, locate and turn the release valve (handle):
a. Clockwise until firm resistance is felt to further turning. This is the 'CLOSED' release valve position used to
raise the saddle.
b. Counter-clockwise, but no more than 1/2 turn from the closed position. This is the 'OPEN' release valve position
used to lower the saddle.
4. With saddle fully lowered, and release valve closed, pump the operating handle. If lift arm responds immediately,
jack is ready for use. If jack does not respond, follow Bleeding/Venting Trapped Air procedure below.
5. Ensure that jack rolls freely. Raise and lower the unloaded saddle throughout the lifting range before putting into
service to ensure the pump operates smoothly. Replace worn or damaged parts and assemblies with Omega
authorized replacement parts only.
Bleeding/Venting Trapped Air
With the Release Valve in the OPEN position (3b above) and Saddle fully lowered, locate and remove the Oil Filler
Plug/Screw. Pump Handle 6 to 8 full strokes. This will help release any pressurized air which may be trapped within
the reservoir. Check oil level and reinstall Oil Filler Plug/Screw.
OPERATION
Lifting
!
WARNING: Only attachments and/or adapters supplied by the manufacturer shall be used.
1. Follow the vehicle manufacturer's recommended guidelines for lifting. Engage the emergency brake and chock
each unlifted wheel in both directions to prevent inadvertent vehicle movement.
2. Close the release valve by turning the handle clockwise
until firm resistance is felt.
3. Refer to the vehicle manufacturer owner's manual to
locate approved lifting points on the vehicle. Center jack
saddle under lift point.
4. Pump handle to contact lift point. To lift, continue pumping
until load reaches desired height.
5. Transfer the load immediately to appropriately rated
jack stands.
Lowering
!
WARNING: Clear all tools and personnel before
lowering load. Open release valve slowly. The further
handle is turned counter-clockwise, the faster the
load will descend. Maintain control of the load at all
times.
1. Raise load high enough to clear jack stands.
2. Remove jack stands.
Handle
(release valve)
Oil Filler Vent Screw
(reference parts drawing for
location)
Saddle
Lifting Arm
Front
Wheel
Caster
Figure 1 - Typical Jack Nomenclature
3
Handle
Fork
Publicidad
