Publicidad
Idiomas disponibles
Idiomas disponibles
BATTERIES
•
The battery supplied is partially charged (to ensure
full capacity of the battery, completely charge the battery
in the battery charger before using your power tool for the
first time)
•
Only use the following batteries and chargers with
this tool
- SKIL battery: BR1*31****
- SKIL charger: CR1*31****
•
Do not use the battery when damaged; it should be
replaced
Do not disassemble the battery
•
•
Do not expose tool/battery to rain
•
Permitted ambient temperature (tool/charger/battery):
- when charging 4...40°C
- during operation –20...+50°C
- during storage –20...+50°C
EXPLANATION OF SYMBOLS ON TOOL/BATTERY
3 Read the instruction manual before use
4 Batteries may explode when disposed of in fire, so do not
burn battery for any reason
5 Store tool/charger/battery in locations where temperature
will not exceed 50°C
6 Do not dispose of electric tools and batteries together
with household waste material
USE
•
Combined switch for on/off and speed control A 2 8 9
- control the speed steplessly from zero to maximum by
putting less or more pressure on the trigger
•
Charging battery
! read the safety warnings and instructions
provided with the charger
•
Removing/installing the battery 2
•
Battery level indicator 7
- press the battery level indicator button F to show the
current battery level.
•
Changing direction of rotation q
- when not properly set in left/right position, switch A
cannot be activated
! change direction of rotation only when tool is at a
complete standstill
•
Changing bits w
! clean and lightly lubricate the SDS+ accessory
before insertion
- pull back locking sleeve C and insert accessory
in SDS+ chuck while turning and pushing it until it
engages; the accessory locks in position automatically
- pull accessory to check that it is locked correctly
- remove accessory by pulling back locking sleeve C
! the SDS+ accessory requires freedom of
movement which causes eccentricity when tool
is off-load; however, the accessory automatically
centres itself during operation without affecting
drilling precision
! do not use bits with a damaged shank
•
Selecting operating mode e
- turn switch D to the desired operating mode until it
snap-locks
1 = normal drilling/screwdriving
2 = impact drilling
3 = chiseling with rotating chisel
4 = chiseling with fixed chisel
All manuals and user guides at all-guides.com
! select operating mode only when tool is switched
off and plug is disconnected
- the hammer mechanism is activated by applying a
slight pressure on the tool when the drill bit is in contact
with the workpiece
- it takes a short time for the hammer mechanism to
reach full impact power
- best hammer drilling results can be obtained by only a
slight pressure on the tool; drilling performance will not
improve by applying more pressure on the tool
•
Chiseling with rotating chisel e
! switch off the tool and disconnect the plug
- select "rotating" chiseling mode
•
Chiseling with fixed chisel r
! switch off the tool and disconnect the plug
- select "rotating" chiseling mode
- place chisel in desired position
- select "fixed" chiseling mode
•
Battery protection
Switches off the tool or prevents the tool from being
switched on, when
- the load is too high
- the battery temperature is not within the allowable
operating temperature range of -20 to +50°C
- the lithium-ion battery is nearly empty (to protect
against deep discharge)
! do not continue to press the on/off switch after the
tool is switched off automatically; battery may be
damaged
•
Adjusting drilling depth u
•
Holding and guiding the tool t
! while working, always hold the tool at the grey-
coloured grip area(s)
- always use auxiliary handle H (can be adjusted as
illustrated) y
- keep ventilation slots E 2 uncovered
- do not apply too much pressure on the tool; let the tool
do the work for you
APPLICATION ADVICE
•
Use the appropriate bits i
! only use sharp bits
•
For drilling with non SDS drill bits in wood, metal and
plastic, use an adapter (not standard included) o
! clean and lightly lubricate the SDS+ accessory
before insertion
- pull back locking sleeve C 2 and insert adapter
in SDS+ chuck while turning and pushing it until it
engages; the adapter locks in position automatically
- pull adapter to check whether is it locked correctly
- set switch D 2 to normal drilling (only activate when
tool is switched off and the switch is locked)
•
When drilling ferrous metals
- pre-drill a smaller hole, when a large hole is required
- lubricate drill bit occasionally with oil
•
When turning in a screw at/near the cross cut end or an
edge of wood, pre-drill a hole in order to avoid cracking
of the wood
•
Splinterfree drilling in wood p
•
Dustfree drilling in walls a
Dustfree drilling in ceilings s
•
•
Drilling in tiles without skidding d
•
For more information see www.skil.com
12
Publicidad
