Balluff BIS V-830-3-011-B-000 Instrucciones Breves página 6

BIS V-830-3-011-B-00_
Mobile RFID devices
About this guide
This guide provides all the information required for the
basic device and the charging and transmission box of the
mobile RFID devices.
It applies to the following models:
BIS V-830-3-011-B-000
–
Ordering code: BIS01FU
Basic device without QR code scanner,
without camera, without NFC
– BIS V-830-3-011-B-001
Ordering code: BIS01FW
Basic device with QR code scanner, with camera,
without NFC
– BIS V-830-3-011-B-002
Ordering code: BIS01H2
Basic device with QR code scanner, with camera,
with NFC
– BAM MD-IS-001-0005
Order code: BAM0421
Charging and transmission box, with power supply unit
Other applicable documents
A comprehensive user's guide and additional information
about this product can be found at www.balluff.com on
the product page.
Intended use
The mobile RFID devices are intended for the mobile
collection and transmission of data and for use in the
industrial sector. The battery and plug-in modules are
solely intended for use with the basic devices and the
charging and transmission box.
Proper function according to the information in the
technical data is only guaranteed if the product is used
solely as described in the user's guide and the associated
documents as well as in compliance with the technical
specifications and requirements and only with a suitable
original Balluff accessory.
Otherwise, it is deemed non-intended use. Non-intended
use is not permitted and will result in the loss of warranty
and liability claims against the manufacturer.
Country-specific WLAN restrictions
– In the EU only WLAN 5 GHz band (5.15...5.35 GHz)
may be operated in indoor areas.
– In France WLAN operation in the outdoor area
(channels 8...13) at 2.454...2.4835 GHz is only
permitted with max. 10 mW.
Max. permissible transmission power
– WLAN 2.4 GHz band: max. 100 mW
– WLAN 5 GHz band: max. 200 mW
– BT-compatible near field communication:
max. 100 mW
– RFID: max. 42 dBμA/m at 10 m distance (magnetic
field strength)
1 english
Reasonably foreseeable misuse
The product is not intended for the following applications
and areas and may not be used there:
– In safety-oriented applications in which personal safety
depends on the device function
– In explosive atmospheres
– In the food contact area
Safety notes
Activities such as installation, connection and startup
may only be carried out by qualified personnel.
Qualified personnel are persons whose technical
training, knowledge and experience as well as knowledge
of the relevant regulations allows him to assess the work
assigned to him, recognize possible hazards and take
appropriate safety measures.
The operator is responsible for ensuring that local safety
regulations are observed.
In particular, the operator must take steps to ensure that a
defect in the product will not result in hazards to persons
or equipment.
The basic device and the charging and transmission box
may only be opened by trained specialists. The other
components (such as the battery) cannot be opened. If
defects and unresolvable faults occur in the product, take
it out of service.
This is a Class A device (EN55032). This device may cause
radio interference in the living area. In this case the
operator may be requested to implement appropriate
measures.
Only original Balluff power supply units as well as batteries
approved by Balluff may be used for the operation of the
basic devices. The use of unauthorized components may
lead to the destruction of the basic devices or the charging
and transmission box. Do not use components with an
external device.
Before use check the components (basic device, battery,
charging and transmission box, power supply unit,
modules) and any connection cables for damage.
Damaged parts must be replaced.
The components (basic device, battery, charging and
transmission box, power supply unit, modules) cannot be
set up in the vicinity of heat sources (such as fan heaters)
and exposed to direct sunlight, excessive dust sources or
vibrations. Observe ambient conditions:
– Operating temperature: −20...+50 °C
– Storage temperature: −20...+60 °C
– Charging temperature: 5...35 °C
In order to avoid overheating, the basic device, battery,
modules, charging and transmission box, as well as the
power supply unit, cannot be covered during operation.