VONROC TS502AC Traducción Del Manual Original página 13

Sawing capacity 0°
Sawing capacity 45°
Thickness of the riving knife
Weight
Lpa (sound pressure level)
Lwa (sound power level)
The declared noise emission value(s) have been
measured in accordance with a standard test method
and may be used for comparing one tool with another;
The declared noise emission value(s) may also be
used in a preliminary assessment of exposure. The
noise emissions during actual use of the power tool
can differ from the declared values depending on
the ways in which the tool is used especially what
kind of workpiece is processed;
Operater must identify safety measures to protect
the operator that are based on an estimation of
exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as
the times when the tool is switched off and when it
is running idle in addition to the trigger time).
DESCRIPTION
The numbers in the text refer to the diagrams on
page 2-6.
1. Table surface
2A. Parallel guide
2B. Guide extension
2C. Wing nuts
3. Ruler for parallel guide
4. Dust extraction
5. Guard
6. Mitre guide
7. Push stick
8. On/off switch
9. 2 in 1 adjustment handle
10. Locking knob
11. Electric plug
12. Ruler sawblade angle
13. Cable storage holder
14. Wrenches (2 pcs)
15. Wing bolts
16. Dust extraction connection
17. Sawblade guard knob
18. Riving knife
19. Saw table inlay
20. Rubber feet (4 pcs)
21. Connection vacuum cleaner
WWW.VONROC.COM
70 mm
50 mm
2.0 mm
10.1 kg
99.6 +3 dB(A)
112.6 +3 dB(A)
22. Fixing screw
23. Carriage-type bolts with nuts
24. Holder clips
25. Overload protection
3. ASSEMBLY
Installing the rubber feet (Fig. A)
• Assemble the bolt to the rubber foot.
• Slide the bolt with rubber foot through the holes
in the corner of the housing.
• Tighten the nut to the bolt of the rubber foot.
• Repeat for each corner of the housing.
Assembly of the riving knife (Fig. A, D)
• Remove the inlay (19) from the table, by using a
screwdriver (Fig. G1).
• Loosen the fixing screw (22)(Fig. D1)
• Raise the riving knife until the depth between
the saw table and the upper edge of the riving
knife equals approx. 110mm (Fig. D2).
• The distance between the riving knife and the
toothed rim of the saw blade must be between
3 and 5 mm (Fig. D3).
• The tip of the riving knife shall not be lower than
5 mm from the tooth peak, as shown in Fig. D3.
Attachment of the guard (Fig. D4)
• Turn sawblade completely upwards (instructi-
ons for height adjustment see chapter 4).
• Pull the knob (17) of the guard (5) and place it
over the riving knife (18) while pulling the knob.
• Release the knob and make sure the pin slides
in the hole.
• Secure the guard by tightening the knob.
Assembly of the dust extraction (Fig. E)
• Assemble dust extraction like shown on Fig. E.
• Attach the vacuum cleaner to the vacuum
cleaner connection (21)(Fig. E).
Attachment of the parallel guide (Fig. F)
• Attach the parallel guide (2A) on the right side
off the saw blade on the table.
• Lock the guide down by pushing down the
handle (Fig. F).
Attachment of the parralel guide holder (Fig. I)
The parallel guide can be stored using the holder
clips (24). Mount the holder clips (24) using carriage -
type bolts with nuts (23). The holders can be mounted
as shown in Fig. J1 or as shown in Fig. J2.
EN
13