Manuales relacionados para Truper MOTB-14
Resumen de contenidos para Truper MOTB-14
- Página 1 Manual Water pump Agricultural use Applies for: Code Model 102432 MOTB-14 MOTB-14 Read the user’s manual thoroughly CAUTION before operating this tool.
- Página 2 Contents CAUTION Technical data Fuel requirements To gain the best performance of the tool, prolong the duty life, General motor tool safety warnings make the Warranty valid if necessary, and to avoid hazards Safety warnings for water pumps of fatal injuries please read and understand this Manual before Parts using the tool.
- Página 3 Technical Data MOTB-14 Code 102432 Description Self-priming motorized pump Engine displacement 36 (cc) Engine rated power 970 W (1.3 Hp) Motor type 4 stroke OHC Speed 6 500 RPM Fuel Gasoline Gasoline tank capacity 0.7 L Fuel efficiency 85 minutes...
- Página 4 General Safety Warnings for Motor Tools Keep your work area clean, tidy and well lit. Wear adequate protective safety accessories. CAUTION CAUTION Cluttered and dark areas may cause accidents. Wear eye protection, dust mask, non-skid safety shoes, helmet and ear plugs. These safety gears reduce the risk Never use the tool in explosive areas or in the presence of injury.
- Página 5 Safety Warnings for Water Pumps Appropriate use Fuel Handling • Do not use the pump to pump flammable or corrosive • Never smoke close to where there is fuel, nor the liquids such as gasoline, oils and acids, neither pumping filling up zone or when operating the pump.
- Página 6 Parts Carry handle Water outlet Fuel tank Water Air filter inlet cover Fuel tank Water drain Pump Base plug Bleed plug Water Throttle Switch outlet Choke lever Rubber Exhaust mounts Starter jack line handle Oil fill plug ENGLISH...
- Página 7 Assembly Mounting of supports • The four rubber mounts must be placed on the base of the tubular chassis to avoid damage to the equipment caused by normal operating vibration. • Insert the tube of the base of the rubber support to fix it to the chassis.
- Página 8 Installation • Place the equipment on a dry, firm, flat and level surface. • Connect one end of the suction hose (not included) to the water inlet of the motor pump (A) and the other end of the hose to the filter (B). •...
- Página 9 Oil and fuel Oil supply (A) Fuel supply (B) • Place the equipment on a flat, level surface. • Place the equipment on a flat and level surface. • Turn and remove the oil fill plug. • Clean and dry the area around the fuel cap. •...
- Página 10 Start up Purge • The system must be purged of any air bubbles by filling the pump with clean water before turning it on. • * Remove the drain plug (A). Fill with water until it reaches the level of the hole and screw on the plug. Only then can the pump be started.
- Página 11 Maintenance CAUTION • Regular and careful maintenance is essential to maintain optimum levels of safety and Carburetor adjustment performance of the equipment. • Before cleaning, repairing, inspecting, or storing • It is recommended to make carburetor adjustments at a Authorized Service Center. equipment, turn off the engine and wait for the engine to cool completely.
- Página 12 Troubleshooting Problem Cause Solution Motor does not start. • The switch is OFF. • Turn ON the switch. • Not enough fuel. • Fill up fuel tank. • Oil level is too low or there is no oil. • Check oil level as indicated in page 9. •...
- Página 13 In the event of any problem contacting a Authorized Service Center, please see our webpage www.truper.com to get an updated list, or call our toll-free numbers 800 690-6990 or 800 018-7873 to get information about the nearest Service Center. DE TODO PARA LA CONSTRUCCIÓN FIX FERRETERÍAS...
- Página 14 11 includes the costs of transportation of the product that derive from its fulfillment of its service network. Phone number 800-018-7873. Made in China. lmported by Truper, S.A. de C.V. Parque Industrial 1, Parque Industrial Jilotepec, Jilotepec, Edo. de Méx. C.P. 54257, Phone number 761-782-9100.