E N G L I S H
manually using the carving for screwdriver on
the shaft end, ventilation
N.B.: Do not run the pump with the water valve
closed as this will ruin irreparably the pump.
At first, when the machine is cold, the steam will
condense rapidly and it is therefore advisable to
wait a few minutes before starting work so that the
condensation can be drained off.
If this is not done, condensation formed will
emerge from the steam pipes, damaging the
garments being processed.
START-UP OF THE MACHINE
(SEE DRAWING PAGE 13-1)
Proceed as follows:
a) Turn on the general electrical supply switch
b) Turn on the main switch of the machine "POS.
69".
c) Turn on the boiler switch "POS. 57.
d) Check on the manometer "POS. 71" that the
steam pressure reaches to 2,5 bar.
USING THE STEAM IRON
(FOR MACHINES WITH CONDENSATE
SEPARATOR)
(SEE DRAWING PAGE 13-1)
Proceed as follows:
a) A few minutes before beginning the finishing
operation switch on the iron switch "POS. 98"
and check that the knob of thermostat is about
at the centre of the middle quadrant.
b) Hold the iron and push at regular intervals the
push button until some steam comes out.
Verify that steam coming out from the iron is
not mixed with water, as in this case this
would mean that the temperature of the iron is
too low therefore wait for some minutes.
c) If necessary, control the quantity of steam flux
by means of the knob of steam valve.
N.B.: for use of the 'Electronic Iron', see the
specific manual relating to the iron.
USING THE HEATED ARM
FORMS
(SEE DRAWINGS PAGE 13-1)
Proceed in the following way:
a) Rotate the arm form that you want to use by
placing it in the work position.
b) Turn on the heating switch for the arm forms
"POS. 69". A thermostat on the inside of the
form controls the heating temperature.
c) To help the use of the aspirator on the arm
form, rotate the lever "POS. 48" counter-
clockwise until the aspirator is completely off
the board and then orient it to the arm form.
C H A P T E R 4
USING THE AIR/STEAM
(SEE DRAWING PAGE 13-1)
Proceed in the following way:
a) Place the part of the item to be cleaned on the
end of the support and press vacuum pedal
"POS. 86".
b) Press the left button of the gun "POS. 36" to
release the steam. For the first few seconds
the steam is mixed with water. Therefore
discharge the gun for a few seconds until it is
well heated.
c) Distribute the jet of steam onto the stain with
the
gun.
dissolves water-soluble stains.
d) If required dry the stained area spray stain
with compressed air by pressing the button on
the right of the gun.
Move the gun rapidly back and forth in a
zigzag motion to remove the dampness in the
stain with the air. The strong, concentrated
vacuum allows rapid drying.
(SEE DRAWING PAGE 13-1)
The board heat temperature is controlled by the
thermostat "POS. 83"; the maximum temperature
that can be set is 90°C=190°F.
N.B.: The entire heated surface can damage
clothing if they remain in contact with it for a long
time. Therefore, do not leave clothing on the
ironing surface for prolonged period of time.
To obtain vacuum in the table, proceed in the
following way:
a) Press pedal "POS. 86" to obtain vacuum in
the table. Vacuum is used to fix trouser
creases and to finishing garments made from
heavy materials (cotton etc.) or on garments
that are very creased.
b) In case of machine with arm shape, rotate the
lever "POS. 48" gradually and clockwise to
obtain the necessary vacuum.
OPERATION OF THE
ELECTRONIC LEVEL CONTROL
When the boiler is empty, the electronic timer,
after 3 seconds from switch on, will call for water
till to cover the probe.
The heating elements are switched off till the
water has reached the water level sensor probe. If
after a further 2 minutes the water has not
reached the right level for work, check that the
water supply valve is not closed and if so, open
the valve and reset the machine. If the water
Page 4-4
SPOTTING GUN
Abundant
steaming
USING THE TABLE
E N G L I S H
instantly