Publicidad
Idiomas disponibles
Idiomas disponibles
Do not charge battery in damp or wet environments
Store tool/charger/battery in locations where temperature will not exceed
Do not use charger when damaged;take it to one of the officially registered Maxpro Service Stations for
a safety check
Do not use charger when cord or plug is damaged;cord or plug should be replaced immediately at one of
the officially registered Maxpro Service Statons
Do not use battery when damaged;is should be replaced immediately
Do not disassemble charger or battery
Do not attempt to recharge non-rechargeable batteries with the charger
If you anticipate long periods of non-use for the tool,it is best to unplug the charger from its power
source.
WHEN CONNECTING NEW 3-PIN PLUG (U.K.ONLY):
Do not connect the blue (=neutral) or brown (=live) wire in the cord of the charger to the earth terminal
of the plug.
If for any reason the old plug is cut off the cord of the charger,it must be disposed of sagely and not left
unattended.
SYMBOLS
Read the manual
Warning
OPERATING INSTRUCTION
4.1 Charging the battery(Fig.1)
The battery is protected from exhaustive discharge.
An integrated protective circuit automatically
Warning! Do not press the ON/OFF switch any more if the protective circuit has actuated. This may damage
the battery.
1. Check that your mains voltage is the same as that marked on the rating plate of the battery charger.
Plug the battery charger in the plug socket and connect the charging cable to the charging connection.
The charging process starts as soon as the charging cable is connected to the charging adapter.
2.The green LED (7) will come on to indicate that the battery pack is being charged.
3.When the charging is completed, the three LEDs indicator will be on. Important! The handle may become
a little warm during the charging process. This is normal.
If the battery pack fails to charge, please check whether there is voltage at the socket-outlet and check for
proper contact with the charging contacts in the battery charger.
Timely recharging of the battery pack will help it serve you well for a long time. You must recharge the
battery pack when you notice that the power of the screwdriver drops.
Never allow the battery pack to become fully discharged. This will cause it to develop a defect.
4.2 Changeover switch (Fig.2/ltem 4)
The slide switch above the ON/OFF switch is for setting the direction of
rotation of the cordless screwdriver and for preventing the cordless
screwdriver frombeing switched on inadvertently.
You can select between clockwise and counterclockwise rotation.Change the direction of rotation
only when
4
GB
50°C or drop below 0°C
Wear dusk mask
Do not dispose of old appliances in the
household garbage
Keep your hands and feet away from all
opening
the equipment is at a standstill. If you fail to observe this point, the gearing may become damaged.
When the slide switch is in the middle position, the ON/OFF switch is blocked.
Never allow the battery pack to become fully discharged. This will cause it to develop a defect.
4.3 Angle setting(Fig.2/ltem 3)
The screwdriver can be locked into two different angle settings. To do so, press the locking button
(3) and move the screwdriver intothe desired position (Press the release button and by turning the
handle (5) to the right). Then release the locking button (3).
Important. Before you switch on the screwdriver, make sure that it is correct-ly locked in the angle
position in question.
4.4 LED working light
The LED working light (2) can be used in poor lighting conditions to illuminate
the area where you want
to screw.
4.5 ON/OFF switch (Fig.3/ Item 6)
Press the On/Off switch to switch the cordless screwdriver on. Release the ON/OFF switch to switch
off the tool.
4.6 Battery capacity indicator (Fig.4/ltem 7)
Press the button ON/OFF switch.
The battery capacity indicator (7) shows the charge state of the battery on three green LEDs.
All LEDs illuminate:
The battery is fully charged.
Two green LED illuminate:
The battery has an adequate remaining charge.
One greed LED:
The battery is empty, recharge the battery.
4.7 Changing the bits (Fig.5)
Important! Set the changeover switch to its center position whenever you carry out any work (for
example changing the bits, maintenance work,etc.)on the cordless screwdriver.
Insert the bit (A) into the bit chuck (1).
CLEANING AND MAINTANCE
When not in use, the product should be stored in a dry and frost-free place to avoid contact with children.
Always keep the product ventilation slot clean to prevent foreign matters from entering. If the shell of the
product needs to be cleaned, do not use solvent, only use wet soft cloth, and regularly blow out the
ventilation slot with compressed air.
ENVIRONMENT
Do not dispose of electric tools,accessories and packaging together with household waste material
- in observance of European Directive 2002/96/EC on waste of electric and electronic equipment
and itsimplementation in accordance with national law,electric tools that hace reached the end of
their life mustbe collected separately and returned to an environmentally compatible recycling facility.
GB
5
Publicidad
