Husqvarna LC 151S Manual De Usuario página 12

2. Fill slowly with a fuel can. If you spill fuel, remove it
with a cloth and let remaining fuel dry off. (Fig. 25)
3. Clean the area around the fuel tank cap.
4. Tighten the fuel tank cap fully. If the fuel tank cap is
not tightened, there is a risk of fire.
5. Move the product a minimum of 3 m (10 ft) from the
position where you filled the tank before a start.
To set the cutting height
1. Move the cutting height lever rearward to increase
the cutting height.
2. Move the cutting height lever forward to decrease
the cutting height. (Fig. 26)
CAUTION:
too low. The blades can hit the ground if the
surface of the lawn is not level.
To start the product
1. Make sure that the ignition cable is connected to the
spark plug.
2. Stay behind the product.
3. Hold the engine brake handle against the handlebar.
(Fig. 27)
4. Hold the starter rope handle with your right hand.
5. Slowly pull out the starter rope until you feel some
resistance.
6. Pull with force to start the engine.
WARNING:
rope around your hand.
To use the drive on the wheels LC
151S & LB 256SP
• Push the drive bail in the direction of the handlebar.
(Fig. 28)
• Release the drive bail to disengage the drive, for
example when you go near an obstacle.
• Before you pull the product rearward, disengage the
drive and push the product forward approximately 10
cm.
To use the drive on the wheels (LB
251S)
• Pull the drive lever in the direction of the handlebar.
(Fig. 29)
• Push the drive lever away from the handlebar to
disengage the drive, for example when you go near
an obstacle.
Note:
The drive lever is automatically disengaged
when you release the engine brake handle.
12
Do not set the cutting height
Do not twist the starter
• Before you pull the product rearward, push the drive
lever away from the handlebar and push the product
forward approximately 10 cm to fully disengage the
drive.
To stop the product
• To stop the drive only, release the drive bail (LC
151S, LB 256SP) or the drive lever (LB 251S).
• To stop the engine, release the engine brake handle.
To use the product with the grass
catcher (LC 151, LC 151S)
WARNING:
without a grass catcher installed or without
the rear cover closed. Objects can eject and
cause injury to the operator.
1. Lift the rear cover and remove the mulch plug if it is
installed. (Fig. 30)
2. Assemble the grass catcher, refer to
the grass catcher (LC 151, LC 151S) on page 11 .
3. Put the grass catcher on the bracket.
4. Release the rear cover and put it on top of the grass
bag frame. (Fig. 31)
To change the product to mulch mode
(LC 151, LC 151S)
Make sure the engine is off before you change the
product to mulch mode.
1. Lift the rear cover and remove the grass catcher, if it
is installed.
2. Put the mulch plug into the discharge channel. (Fig.
32)
3. Close the rear cover and make sure that it is tightly
closed against the mulch plug.
Note:
To increase the performance of the mulch
mode, replace the blade with the mulch blade
To replace the blade on page 14
accessory. Refer to
To change the product to side
discharge mode
1. Lift the rear cover and remove the grass bag, if it is
installed.
2. Close the rear cover and make sure that it is tightly
closed against the product.
3. Lift the discharge lock. (Fig. 33)
4. Open the side discharge cover and install the side
discharge deflector onto the support pins. (Fig. 34)
5. Let the side discharge cover close against the
side discharge deflector. Make sure that the side
discharge deflector is tightly in position before you
operate the product.
Do not operate the product
To assemble
1924 - 002 - 12.10.2022