Publicidad
Idiomas disponibles
Idiomas disponibles
CHARACTERISTICS
▶Power: 900/1.200/2.100W
ES
▶3 levels
▶Security grid
PT
ASSEMBLY INSTRUCTIONS
EN
FR
1: additional anchor chain with 2 carabiners
2: standard fixing chain with a carabiner at the end
▶The heater must be hung 40 cm from the surface. The hanging chain
measures 40 cm.
▶In addition, at least 50 cm of space must be left on the sides,
between the device and any side walls, tent canvas or other objects.
There must also be at least 1.80m between the floor and the bottom
of the heater. The appliance must never be hung on a hook on the
wall, as there could be a tilt!
▶There are two hanging methods:
• 1- On the roof
• 2- In a frame (for example a store frame)
HANG ON THE CEILING
▶The appliance must be hung on a concrete ceiling. Never hang it on a
ceiling made of wood, plaster or any other material! Fixing materials
and fire safety measures are not suitable for this type of installation.
▶Find a place on the roof that meets all the requirements.
▶Drill a sufficiently deep hole with a diameter of 8mm.
▶Turn the stud clockwise and check that the pendant is screwed onto
the stud correctly and that the stud is secure. Make sure the fixing
kit can bear the weight of at least 15kg.
▶Hang the heater in the eye of the pendant with the carabiner so that
the heater is 40 cm from the ceiling.
▶Check that the carabiner hook is properly closed.
Instruction manual
HANG OVER A FRAME (FOR EXAMPLE, A STORE FRAME)
▶Make sure that the heater can hang freely from the chosen fixing
▶Find a location in the framework that meets all the requirements.
▶Use the additional accessory chain with a carabiner at each end to
▶Hook the extra chain to the end link on the hanging chain that is
▶Next, connect the second carabiner to the same link on the hanging
▶Check that the carabiner hook is securely closed and that the heater
Careful! The top and bottom cover of the heater gets hot when it is
turned on. That is why distances are so important.
▶Route the electrical cable along the hanging chain and secure it at
FUNCTIONING
▶Before connecting the device to the network, make sure that the
▶Plug the power cord into the AC 220-240V~ 50Hz outlet.
▶Through the 3 power system you can start the appliance.
▶If you do not use the appliance for a long time, unplug the power
▶Never try to disassemble the device.
▶If you notice any abnormality (such as unusual noise from the
▶Do not use this heater with a programmer, timer or other device that
▶Make sure that no objects or liquids get inside the appliance through
▶The device must only be used in dry environments. Do not use in the
▶Protect the device from dust, moisture, sunlight, and direct heat.
point (respecting all distances) and that it is strong enough to
support the weight of the heater. Secure it so it cannot fall, slide, or
otherwise move.
effectively secure:
attached to the heater using the carabiner.
chain, which will ensure that the heater remains 40cm from the
ceiling.
is securely attached. It shouldn't slip, give, or move at all!
several points. Make sure the cable is tight along the chain but no
force is exerted on it, it is important that the heater does not get
hung up on the cable!
switch is in the "0" position.
• POSITION 0: OFF position, no button pressed.
• POSITION 1: first speed - 900W
• POSITION 2: second speed - 1,200W
• POSITION 3: third speed - 2,100W
cord from the electrical outlet.
device), turn off the device and unplug it immediately.
switches the heater on automatically, as there is a risk of fire if the
heater is covered or incorrectly positioned
the openings.
immediate vicinity of a bathtub, shower or swimming pool
Ref. 07092
Publicidad
