Descargar Imprimir esta página

BTI ST 160 E Manual Original página 25

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 10
accessories, or storing power tools. Such pre-
ventive safety measures reduce the risk of start-
ing the power tool accidentally.
 Store idle power tools out of the reach of chil-
dren and do not allow persons unfamiliar with
the power tool or these instructions to operate
the power tool. Power tools are dangerous in
the hands of untrained users.
 Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool's operation. If damaged, have the
power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
 Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
 Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed. Use of the pow-
er tool for operations different from those intend-
ed could result in a hazardous situation.
Service
 Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the pow-
er tool is maintained.
Safety Warnings for Jigsaws
 Hold power tool by insulated gripping surfac-
es, when performing an operation where the
cutting accessory may contact hidden wiring
or its own cord. Cutting accessory contacting a
"live" wire may make exposed metal parts of the
power tool "live" and could give the operator an
electric shock.
Additional Safety and
Working Instructions
 Keep hands away from the sawing range. Do
not reach under the workpiece. Contact with
the saw blade can lead to injuries.
 Apply the machine to the workpiece only when
switched on. Otherwise there is danger of kick-
back when the cutting tool jams in the workpiece.
1 609 92A 0CD • 4.11.13
 Pay attention that the base plate rests secure-
ly on the material while sawing. A jammed saw
blade can break or lead to kickback.
 When the cut is completed, switch off the ma-
chine and then pull the saw blade out of the
cut only after it has come to a standstill. In this
manner you can avoid kickback and can place
down the machine securely.
 Use only undamaged saw blades that are in per-
fect condition. Bent or dull saw blades can break,
negatively influence the cut, or lead to kickback.
 Do not brake the saw blade to a stop by apply-
ing side pressure after switching off. The saw
blade can be damaged, break or cause kickback.
 Use suitable detectors to determine if utility
lines are hidden in the work area or call the lo-
cal utility company for assistance. Contact with
electric lines can lead to fire and electric shock.
Damaging a gas line can lead to explosion. Pen-
etrating a water line causes property damage or
may cause an electric shock.
 Secure the workpiece. A workpiece clamped
with clamping devices or in a vice is held more
secure than by hand.
 Always wait until the machine has come to a
complete stop before placing it down. The tool
insert can jam and lead to loss of control over the
power tool.
 Before any work on the machine itself, pull the
mains plug.
 Do not direct the light beam at persons or ani-
mals and do not stare into the light beam your-
self (not even from a distance).
 Check the tight seating of the saw blade. A
loose saw blade can fall out and lead to injuries.
 The saw blade should not be longer than re-
quired for the intended cut. Use a narrow saw
blade when sawing tight curves.
 When ejecting the saw blade, hold the ma-
chine in such a manner that no persons or an-
imals can be injured by the ejected saw blade.
 Dusts from materials such as lead-containing
coatings, some wood types, minerals and met-
al can be harmful to one's health and cause al-
lergic reactions, lead to respiratory infections
and/or cancer. Materials containing asbestos
may only be worked by specialists.
– As far as possible, use a dust extraction sys-
tem suitable for the material.
– Provide for good ventilation of the working
place.
– It is recommended to wear a P2 filter-class res-
pirator.
English | 25

Publicidad

loading