Publicidad
Idiomas disponibles
Idiomas disponibles
ASSEMBLY INSTRUCTIONS
13. Using a stud finder (not included), locate the
edges of the wood studs. Find the center line of each
stud and draw a vertical reference line on the wall
over each one. Position installation template (O) at
desired location on wall.
Note: The bottom of the installation template (O)
should be no less than 31-1/2 in. from the floor.
Mark mounting holes with a pencil (not included) and
discard installation template (O). Drill 3/16 in. pilot
holes at marked locations. Then, with the beveled
edge facing up, attach the wall hanging cleats (L)
with large flat washers (II) and M8 x 2-1/2 in. lag bolts
(HH).
Hardware Used
HH
M8 x 2-1/2 in. Lag Bolt
II
Large Flat Washer
14. With the help from another person, carefully hang the
unit onto wall hanging cleats (L).
Pole Installation
15. Insert 22 mm metal poles (N) into 25 mm metal
poles (M). Using closed pole holders (RR) as a
guide, mark screw hole locations with a pencil. Drill
3/8 in. diameter pilot holes at least 2-1/2 in. deep at
marked locations, then insert drywall anchors (not
included) into the holes. Attach closed pole holders
(RR) with M4 x 38 mm zinc screws (OO). Insert 25
mm metal poles (M) into closed pole holders (RR),
securing with M4 x 15 mm self-tapping screws (SS).
Note: Drywall anchors are not required if installing
into a stud.
Hardware Used
RR
Closed Pole Holder
SS
M4 x 15 mm Self-tapping Screw
OO
M4 x 38 mm Zinc Screw
13
Wooden Stud
16 in.
L
39-1/2 in.
L
O
Minimum 31-1/2 in.
14
x 4
x 4
L
L
L
15
M
SS
x 2
x 2
Drywall Anchor
x 6
OO
(not included)
RR
Lowes.com/allenandroth
10
ASSEMBLY INSTRUCTIONS
16. Attach open pole holders (QQ) to upper left side
panel (A) and upper right side panel (B), with M4 x 14
mm zinc wood screws (PP). Insert 22 mm metal poles
(N) into open pole holders (QQ), securing with M4 x 15
II
mm self-tapping screws (SS).
HH
Hardware Used
PP
M4 x 14 mm Zinc Wood
Screw
II
QQ
Open Pole Holder
HH
SS
M4 x 15 mm Self-tapping Screw
Adjustable Shelf Installation
15. Insert shelf pins (GG) where desired in cabinet,
then rest adjustable shelf (F) on top.
Note: Ensure the shelf pins (GG) are level.
Hardware Used
GG
Shelf Pin
CARE AND MAINTENANCE
•
Periodically check to make certain all components are properly positioned, free from damage
and firmly connected.
•
Use a soft, clean cloth that will not scratch the surface when dusting.
N
•
Never use water to clean the furniture as it may cause damage to the finish.
•
Wipe clean using a damp cloth and a mild cleaner. Wipe dry with a clean cloth.
•
In the event that the furniture is stained or otherwise damaged during use, it is recommended
you call a professional to repair the furniture.
•
Keep furniture away from direct sunlight as it may damage the finish.
•
It is best to keep the furniture in a climate-controlled environment. Extreme temperature and
humidity changes can cause fading, warping, shrinking and splitting of wood.
RR
•
Touch-up pen (MM) has been provided (except in Item #1465188/1465189) to repair any small
nicks or scratches that may occur during assembly or shipping.
•
If Item #1465188/1465189 is damaged and touch-up is required please apply a quality wood
polish to the damaged surface. Polish not included with this item.
16
QQ
SS
x 6
x 2
x 2
QQ
PP
17
GG
x 8
F
F
Lowes.com/allenandroth
11
Publicidad
