TEFAL PerfectMix BL88A8 Manual De Instrucciones página 52

ADVICE
• Depending on the nature of the ingredients, you can use the blender
jug to prepare up to
* 1.5 L for thick mixtures.
* 1.25 L for liquid preparations.
Warning : Do not pour boiling liquids (over 80°C/176°F) in the jug.
• You can prepare finely blended soups, cream soups, stewed fruit, light
batter (pancakes, fritters, Yorkshire pudding batter, etc.), milkshakes,
smoothies, cocktails, etc.
• If ingredients stick to the sides of the jug when blending, stop the
appliance. Remove the blender jug from the motor unit, and push the
food down onto the blades using a spatula and put your blender jug
back to continue your preparation.
• Always pour the liquid ingredients into the blender jug first, before
adding the solid ingredients, without exceeding the maximum level.
• To add ingredients while blending, remove the lid cap (F6, O6) from the
lid (F5, O5) and add the ingredients through the feeder hole.
• For finely crushed ice, use a maximum of 6 small ice cubes (25x25x25 mm
maximum) using "Ice crush" function. There is no need to add water.
• Always operate the blender with lid or guard in position as indicated in
the instructions. Never put a hand in the jar when it is placed on the base
unit, if food needs to be pushed down use a suitable tool e.g. spatula
RECIPE
Cold carrot soup:
600g carrots + 900g water : Put the water in the blender jug and add the
carrot pieces. Mix on max speed for 3 minutes.
CLEANING
Do not immerse the appliance in water. Never put the motor unit (A)
under running water.
• Clean the jug immediately after use.
• Fill up the jug with 1 litre of hot water along with 2 or 3 drops of washing
up liquid. Only use the recommended amount of water and washing
up liquid. An excess of washing up liquid creates more foam and
consequently can lead to overflowing.
98
• Use the automatic auto clean program to carry out a prewash of the jug.
• Once the program has stopped, unplug the appliance.
• Remove the blender jug (F4, O4)
• Place the jug on a flat surface.
• Unlock the lid and remove it with care. Pour out the water.
• Remove the Blade Unit + Locking Ring + Seal (F1 + F2 + F3 / O1 + O2
+O3) and clean them under running water. The blades are very sharp,
handle them with caution to avoid injury (Fig. 10).
18
• After cleaning, remember to correctly fit the seal (F3, O3) back onto the
blade unit (F1, O1) (Fig. 17). Please be careful to avoid any damage to
the seal by touching the blades.
Note: Incorrectly fitting the seal can result in ingredients leaking from
the base of the blender jug.
• Rinse the inside of the jug and the lid under running water.
• Take care when cleaning the blades in the blender jug and when you
empty the jug as they are sharp.
• Use a damp cloth to clean the motor unit (A). Dry it carefully.
• The detachable parts (lid, blade unit, locking ring,) can be cleaned with
a sponge and hot soapy water.
• The jug (F4, O4), blade unit without titanium coating (F1), locking ring
(F2, O2) can be cleaned in the dishwasher on the upper rack - use the
'ECO' or 'LOW SALT' program.
• Caution: The jug (F4, O4), blade unit without titanium coating (F1) and
locking ring (F2, O2) must be disassembled and placed separately in the
dishwasher. Please do not put the blades with titanium coating (O1) in
the dishwasher.
19
EN
99