Active Era AB-K3 Manual De Instrucciones página 5

Rechargeable Air Pump
Prior to using the rechargeable air pump ensure that it is fully charged.
To charge the rechargeable air pump:
1. Remove the power inlet cap.
2. Insert the power connector of the USB charging cable into the power inlet.
3. Leave to charge. Note, whilst charging the charging indicator light on the USB
charging cable will show as red.
4. Full charge will be achieved within 4 hours. When fully charged the charging
indicator light on the USB charging cable will show as blue.
5. Once charged remove the power connector and replace the power inlet cap.
Inflation
Rechargeable Air Pump
1. Choose a flat surface large enough to accommodate the inflated air bed.
2. Remove any sharp or pointed objects on or near the surface.
3. Lay the air bed out with the bottom non-flocked surface touching the floor.
4. Open the first stage of the two stage air valve.
5. Remove the power inlet cap on the rechargeable air pump.
6. Insert the inflation nozzle into the first stage of the two stage air valve. Use the
nozzle adapters to ensure a secure fit.
7. Turn the power button on and inflate the air bed to the desired firmness.
8. Remove the inflation nozzle, close the first stage of the two stage air valve,
turn the power button off, and replace the power inlet cap on the rechargeable
air pump.
9. The air bed is now ready for use.
Integrated Foot Pump
1. Choose a flat surface large enough to accommodate the inflated air bed.
2. Remove any sharp or pointed objects on or near the surface.
3. Lay the air bed out with the flocked surface touching the floor.
4. Remove the screw cap and rubber bung from the top of the integrated foot
pump and place safely to one side.
5. Standing with your foot on top of the integrated foot pump press down and lift
up in a repeating motion to inflate the air bed to the desired firmness.
6. Replace the screw cap and rubber bung ensuring that the fit is secure.
7. Turn the air bed over so that that non-flocked surface is touching the floor.
8. The air bed is now ready for use.
Deflation
Rechargeable Air Pump
1. To deflate the air bed, open the second stage of the two stage air valve to fully
open the air valve.
8 | English
2. Remove the power inlet cap on the rechargeable air pump.
3. Insert the deflation nozzle into the second stage of the two stage air valve. Use
the nozzle adapters to ensure a secure fit.
4. Turn the power button on and deflate the air bed.
5. Remove the deflation nozzle, close the second stage of the two stage air
valve, turn the power button off, and replace the power inlet cap on the
rechargeable air pump.
6. The air bed is now ready to pack away.
Two Stage Valve
1. To deflate the air bed, open the second stage of the two stage air valve to fully
open the air valve.
2. From the end of the air bed opposite the two stage valve slowly fold up or roll
the air bed up in the direction of the two stage valve thereby forcing the air out
of it.
3. Once fully deflated close the the second stage of the two stage air valve.
4. The air bed is now ready to pack away.
FREQUENTLY ASKED QUESTIONS
Why is my air bed deflating?
There are a few reasons your air bed may be losing air:
• First Uses: During its first few uses, your Active Era Air Bed may sag and
require additional inflation to maintain its desired firmness. This is because
stretching is a natural characteristic of new vinyl and is normal for the first few
days of use. Inflate your air bed at least 30 minutes prior to first use and top
up as required to allow the air bed to stretch to its natural shape.
• Normal Use: All air beds are designed to lose a small amount of air through
their seams during use to reduce the risk of tears and bursting when pressure
is added. This also helps to prevent over-inflation.
• Increased Pressure: Your air bed may be deflating because the weight limit
has been exceeded. Most of our air beds have a weight limit of 250kgs or
550lb. Please check the product page or the specifications in your instruction
manual for product specific weight limits.
• Varying Temperatures: Air inside the air mattress can expand or contract
when exposed to hot or cold temperatures. At cold temperatures, air naturally
contracts inside the air bed and can lead to sagging. If deflation occurs, pump
some more air into the mattress. At hot temperatures, air can expand inside
the air bed and it will become hard and in extreme circumstances, burst.
Release air to avoid damage to your air bed. Where possible, aim to keep
English | 9