Fein Grit GIMS75 2H Manual página 13

If the belt tracking cannot be adjusted centred:
Clean the drive wheel (12) and the contact wheel (13)
with compressed air.
Check the drive wheel and the contact wheel for wear,
deformation and damage. Have damaged components
replaced without delay!
Replacing the grinding belt.
Before any work on the machine itself, pull the
mains plug.
Loosen screw (14) and fold down the side cover (15).
Tilt lever (16) downward to release
the tensioning device.
Remove the old grinding belt.
Before mounting the new grinding
belt, observe the running-direction
indication on the rear of the grinding belt! It mus corre-
spond with the rotation direction of the drive wheel.
Place the grinding belt both around the drive wheel (12)
and around the contact wheel (13).
Tilt lever (16) upward to tension the
grinding belt.
If the grinding belt can not be ten-
sioned sufficiently, the tensioning
device must be readjusted. Loosen
both screws (17), change the position of the tensioning
device and retighten the screws.
Shut the side cover (15) and tighten screw (14) again.
Mount the grinding rest (7) and the chip/grinding-dust
box (8).
Check the gap size of the grinding rest.
Switch the machine on and adjust the belt run.
Operating instructions.
Switching on:
Press pushbutton "I" (18).
Switching off:
Press pushbutton "0" (18).
Switching on: (only 2H models)
Press switch "I" (18).
Switching off: (only 2H models)
Press switch "I" (18).
After switching off, the machine runs on for
approx. 50 seconds.
Safety pushbutton (20):
In situations of danger, press the safety pushbutton to
switch the machine off.
Reversing the speed (19) (only 2H models)
Switch position 1: Low speed
Switch position 2: High speed
The speed may only be reversed with switch (19)
when the machine is stopped.
Overload protection.
In case of continuous high load over a longer period of
time, the machine is switched off. After a cooling-down
period of approx. 15 minutes, the machine is ready for
operation again.
Working instructions.
Move the undercarriage to the workplace.
Switch the belt grinder on and pull the steering-bar lever
to the working position.
Guide the belt grinder with uniform speed over the sur-
face to be ground.
After completing the working procedure, tilt the steering
bar upward and switch the belt grinder off.
Noise emission values.
A-weighted emission
pressure power level
measured at the work-
place L (re 20 μPa), in
pA
decibels
Measuring uncertainty
K , in decibels
pA
Measured A-weighted
sound power level L
wA
(re 1 pW), in decibels
Measuring uncertainty
K , in decibels
wA
Operating conditions
Speed (rpm)
Material
Dimension
Grinding belt
REMARK: The sum of the measured emission value and
respective measuring inaccuracy represents the upper
limit of the values that can occur during measuring.
Wear hearing protection!
Measured values determined in accordance with the cor-
responding product standard (see last page in this Instruc-
tion Manual).
Repair and customer service.
Repairs may be carried out only by qualified per-
sons in conformity with the valid regulations.
For repairs, we recommend our FEIN customer service
centre, the FEIN authorised service centres and FEIN
agencies.
When the machine's power supply cable is damaged, it
must be replaced using a specially prepared power supply
cable, available from your FEIN customer service agent.
The current spare parts list of this machine can be found
on the Internet under www.fein.com.
en
13
Idle Sanding
80.5 94
4 4
90 100,5
2.5 2.5
3 000 3 000
– ST 37
– 8 x 40
GRIT by Fein
– 36Z