Publicidad
Idiomas disponibles
Idiomas disponibles
b) Do not expose battery pack to heat or fire. Avoid
storage in direct sunlight.
c) Do not short-circuit a battery pack. Do not store
battery packs haphazardly in a box or drawer
where they may short-circuit each other or be
short-circuited by conductive materials. When
battery pack is not in use, keep it away from other
metal objects, like paper clips, coins, keys, nails,
screws or other small metal objects, that can make a
connection from one terminal to another. Shorting the
battery terminals together may cause burns or a fire.
d) Do not remove battery pack from its original
packaging until required for use.
e) Do not subject battery pack to mechanical shock.
f) In the event of battery leaking, do not allow the
liquid to come into contact with the skin or eyes.
If contact has been made, wash the affected area
with copious amounts of water and seek medical
advice.
g) Observe the plus (+) and minus (–) marks on the
battery back and equipment and ensure correct
use.
h) Do not use any battery pack which is not
designed for use with the equipment.
i) Keep battery pack out of the reach of children.
j) Seek medical advice immediately if a cell or
battery pack has been swallowed.
k) Always purchase the battery pack recommended
by the device manufacturer for the equipment.
l) Keep battery pack clean and dry.
m) Wipe the battery pack terminals with a clean dry
cloth if they become dirty.
n) Battery pack needs to be charged before use.
Always use the correct charger and refer to
the manufacturer's instructions or equipment
4
manual for proper charging instructions.
o) Do not leave battery pack on prolonged charge
when not in use.
p) After extended periods of storage, it may
be necessary to charge and discharge the
battery pack several times to obtain maximum
performance.
q) Battery pack gives its best performance when it
is operated at normal room temperature (20 °C ±
5 °C).
r) When disposing of battery packs, keep battery
packs of different electrochemical systems
separate from each other.
s) Recharge only with the charger specified by
Worx. Do not use any charger other than that
specifically provided for use with the equipment.
A charger that is suitable for one type of battery pack
may create a risk of fire when used with another
battery pack.
t) Retain the original product literature for future
reference.
u) Use only the battery pack in the application for
which it was intended.
v) Remove the battery from the equipment when
not in use.
w) Dispose of properly.
SAVE THESE INSTRUCTIONS
Cordless Chainsaw
Instructions concerning the proper techniques for
basic felling, limbing, and cross-cutting
1. Felling a tree
When bucking and felling operations are being performed
by two or more persons at the same time, the felling
operations should be separated from the bucking
operation by a distance of at least twice the height of the
tree being felled. Trees should not be felled in a manner
that would endanger any person, strike any utility line or
cause any property damage. If the tree does make contact
with any utility line, the company should be notified
immediately.
The Chain saw operator should keep on the uphill side of
the terrain as the tree is likely to roll or slide downhill after
it is felled.
An escape path should be planned and cleared as
necessary before cuts are started. The escape path should
extend back and diagonally to the rear of the expected line
of fall as illustrated in Figure 1.
Before felling is started, consider the natural lean of the
tree, the location of larger branches and the wind direction
to judge which way the tree will fall.
Remove dirt, stones, loose bark, nails, staples and wire
from the tree.
2. Notching undercut
Make the notch 1/3 the diameter of the tree, perpendicular
to the direction of falls as illustrated in Figure 2. Make the
lower horizontal notching cut (W) first. This will help to
avoid pinching either the saw chain or the guide bar when
the second notch (X) is being made.
3. Felling back cut
Make the felling back cut (Y) at least 2'' higher than the
horizontal notching cut as illustrated in Figure 2. Keep the
felling back cut parallel to the horizontal notching cut.
Make the felling back cut so enough wood is left to act
as a hinge. The hinge wood keeps the tree from twisting
and falling in the wrong direction. Do not cut through the
hinge.
As the felling gets close to the hinge, the tree should begin
to fall. If there is any chance that the tree may not fall in
desired direction or it may rock back and bind the saw
chain, stop cutting before the felling back cut is complete
and use wedges of wood, plastic or aluminium (Z) to open
the cut and drop the tree along the desired line of fall (
When the tree begins to fall remove the Chain saw from
the cut, stop the motor, put the Chain saw down, then use
the retreat path planned (
falling and watch your footing.(See Fig.1)
Fig.1
2˝
X
Z
Y
W
2˝
). Be alert for overhead limbs
3
1
1
2
1
EN
).
2
Publicidad
