Publicidad
Idiomas disponibles
Idiomas disponibles
Reconnect the nozzle to the spray wand.
Turn on the water supply and start the engine.
PUMP LUBRICATION
The pump on this product was lubricated with a sufficient
amount of high grade lubricant for the life of the unit under
normal operating conditions. Therefore, no further lubrica-
tion is required.
PUMP MAINTENANCE
Routinely make a visual inspection of the pump. If you notice
any leaking of lubricant around the pump oil seals, take the
pressure washer to an qualified service center for repair.
There are no user serviceable parts to the pressure washer
pump. Any attempt to service or alter the pump may dam-
age the pressure washer and void your product warranty.
USING THE BATTERY MAINTAINER CHARGER
See Figure 23.
When storing the pressure washer, connect the battery
maintainer charger to keep the battery fully charged and
ready for use.
NOTE: The battery maintainer charger model LC-2533
provided should only be used with the 12V 4.5Ah/20HR
sealed lead acid battery model LPL 12-4.5 supplied with
this pressure washer.
Plug the battery maintainer charger into a standard house-
hold 120V receptacle. Make sure the household power
supply is 120V, AC only, 60 Hz.
NOTE: The green LED light will indicate the power is on.
Disconnect the starter cable on the pressure washer from
the connection port on the battery.
Connect the battery maintainer charger to the connection
port on the battery. The light on the battery maintainer
charger will illuminate red while the battery is charging.
The battery will become slightly warm to the touch while
charging. This is normal and does not indicate a problem.
When battery is fully charged, the red light will turn green.
NOTE: If the light does not illuminate, the battery main-
tainer fuse may need to be replaced. Check the fuse and
replace if needed.
When ready to use pressure washer:
Disconnect the charger from the power outlet first, then
disconnect the output leads from the battery.
Reconnect the starter cable on the pressure washer to
the connection port on the battery, making sure the plug
is fully seated.
MAINTENANCE
REPLACING THE BATTERY
See Figures 24 - 25.
WARNING:
To reduce the risk of electric shock or explosion, do not
short circuit the battery terminals or charge in a sealed
container. Keep sparks and flame away. Do not use
metal tools for connections and keep metal objects away
from the battery terminals. Metal objects can make a
connection from one terminal to another. Shorting the
battery terminals together can cause sparks, burns, or
a fire.
Disconnect the starter cable on the pressure washer from
the connection port on the battery.
Push the starter cable through the hole in the battery
bracket.
Using a 10 mm wrench or socket (not provided), remove
the nuts, T-30 Torx bolts, and washers securing the soap
tank and battery bracket to the pressure washer frame.
Lift the soap tank and remove the battery bracket.
NOTE: Be careful not to disconnect the soap injection
hose from the back of the soap tank.
Remove the T-30 Torx bolts and washers securing the
battery holder to the battery bracket. Remove the battery
holder from the bracket and set the bracket aside.
Disconnect the battery holder from the battery:
• Disconnect the black wire from the battery's negative
(–) terminal.
• Disconnect the red wire from the battery's positive (+)
terminal.
Remove the old battery and dispose of according to local
and state regulations. Always abide by the safety warnings
provided with the battery.
Connect the battery holder to the new battery:
• Connect the red wire to the battery's positive (+) terminal.
• Connect the black wire to the battery's negative (–)
terminal.
Place the battery holder with the new battery installed
onto the battery bracket in the same orientation as the
old one.
Reinstall the washers and bolts and tighten securely.
Lift the soap tank and replace the battery bracket back
in position.
NOTE: Make sure the soap injection hose is firmly seated
on the hose barb on the back of the soap tank.
Reinstall the nuts, bolts, and washers securing the soap
tank and battery bracket to the pressure washer frame.
Tighten securely.
Push the starter cable through the hole in the battery
bracket.
Reconnect the starter cable on the pressure washer to
the connection port on the battery, making sure the plug
is fully seated.
Page 15 — English
Publicidad
