Publicidad
Idiomas disponibles
Idiomas disponibles
e. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts and
any other condition that may affect the power tools
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
5. Service
a. Have your power tool serviced by a quali ed repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
@
Additional power tool safety warnings
Warning! Safety instructions for all saws
Hold power tool by insulated gripping surfaces, when
performing an operation where the cutting accessory
may contact hidden wiring. Cutting accessory contacting
a "live" wire may make exposed metal parts of the power
tool "live" and could give the operator an electric shock.
Use clamps or another practical way to secure and
support the workpiece to a stable platform. Holding
the work by hand or against your body leaves it unstable
and may lead to loss of control.
Keep hands away from cutting area. Never reach
underneath the work piece any reason. Do not insert
ngers or thumb into the vicinity of the reciprocating blade
and blade clamp. Do not stabilize the saw by gripping
the shoe.
Keep blades sharp. Dull or damaged blades may cause
the saw to swerve or stall under pressure. Always use the
appropriate type of saw blade for the workpiece material
and type of cut.
When cutting pipe or conduit, make sure that they
are free from water, electrical wiring, etc.
Do not touch the workpiece or the blade immediately
after operating the tool. They can become very hot.
Be aware of hidden hazards, before cutting into walls,
oors or ceilings, check for the location of wiring
and pipes.
The blade will continue to move after releasing the
switch. Always switch the tool off and wait for the saw
blade to come to a complete standstill before putting the
tool down.
(Original instructions)
(Original instructions)
Warning! Contact with, or inhalation of dusts arising from
cutting applications may endanger the health of the operator
and possible bystanders. Wear a dust mask speci cally
designed for protection against dust and fumes and ensure
that persons within or entering the work area are also
protected.
The intended use is described in this instruction manual.
The use of any accessory or attachment or performance
of any operation with this tool other than those
recommended in this instruction manual may present
a risk of personal injury and/or damage to property.
Safety of others
This tool is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliance by a person responsible
for their safety.
Children should be supervised to ensure that they
do not play with the appliance.
Vibration
The declared vibration emission values stated in the technical
data and the declaration of conformity have been measured
in accordance with a standard test method provided by
EN 60745 and may be used for comparing one tool with
another. The declared vibration emission value may also
be used in a preliminary assessment of exposure.
Warning! The vibration emission value during actual use of
the power tool can differ from the declared value depending
on the ways in which the tool is used. The vibration level
may increase above the level stated.
When assessing vibration exposure to determine safety
measures required by 2002/44/EC to protect persons regularly
using power tools in employment, an estimation of vibration
exposure should consider, the actual conditions of use and the
way the tool is used, including taking account of all parts of the
operating cycle such as the times when the tool is switched off
and when it is running idle in addition to the trigger time.
Labels on tool
The following symbols are shown on the tool:
:
Warning! To reduce the risk of injury, the user
must read the instruction manual.
ENGLISH
ENGLISH
5
5
Publicidad
