Descargar Imprimir esta página

Kärcher KM 85/50 R Bp Pack 80 Ah Li + FC Manual Del Usuario página 23

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 58
Emptying the waste container
Transport rolls
1
Waste container
2
Waste container lock
3
1. Clean the dust filter with the manual filter cleaner.
2. Open the lock on the waste container.
3. Pull out the waste container.
4. Empty the waste container.
When emptying the waste container, make sure that the seal-
ing strip does not become damaged.
5. Raise the waste container at the front and push it in all the way.
6. Check whether the waste container has clicked into place.
Stopping and parking the device
1. Take your foot from the accelerator.
2. Raise the roller brush and side brush.
3. Remove the ignition key.
4. Charge the battery.
5. Empty the waste container.
6. Only park the device on an even surface (< 2% gradient).
Transport
CAUTION
Risk of injury and damage
Be aware of the weight of the device during transportation.
1. The device has 4 marked lashing points. They are for use
when fastening the device.
2. When transporting the device on vehicles, secure it to prevent
it from slipping or overturning in accordance with the respec-
tive valid guidelines.
Storage
CAUTION
Failure to observe the weight
Risk of injury and damage
Be aware of the weight of the device during storage.
● This device may only be stored indoors.
● Before storing for a longer period of time, carry out the follow-
ing steps:
1. Bring the battery pack to a state of charge between 30% and
50%.
2. Disconnect the charger from the battery connector.
3. Put the battery pack into sleep mode:
a Plug in the battery connector on the device.
b Switch on the device (turn the ignition key to "1") and wait
until the device is ready.
c Press and hold the button on the battery pack for at least 20
seconds until all 5 LEDs light up and then go out one after
the other. The charge indicator will now no longer react
when the button is pressed briefly.
d Switch off the device with the ignition key and switch it on
again after waiting for 5 seconds.
Note
When the sleep mode has been successfully activated, the de-
vice remains switched off and the display remains off. If the de-
vice switches on as usual, steps a-d must be repeated to
establish sleep mode.
4. Set the ignition key to "0".
Note
For devices with multiple batteries, this procedure only needs to
be carried out on one battery. The other batteries take over the
sleep mode automatically. After establishing sleep mode, do not
connect the battery pack to the charger again - this interrupts the
sleep mode!
Care and maintenance
DANGER
Risk of accidents and injuries due to unintentional move-
ment of the device
Switch off the device before carrying out any care and mainte-
nance work, and remove the ignition key.
Disconnect the central battery plug connector.
Note
● Adhere to the safety instructions for care and maintenance.
CAUTION
Risk of short circuits due to water stream
Do not clean the device with a hose or high-pressure water jet.
DANGER
Health risk from dust
Wear a dust mask and safety goggles when cleaning with com-
pressed air.
ATTENTION
Risk of damage to the surfaces
Do not use any scouring agents or aggressive cleaning agents for
cleaning purposes.
1. Blow out the inside of the device with compressed air.
2. Clean the inside and outside of the device with a damp cloth,
soaked in mild washing lye.
Service hours counter / operating hours / battery charge
ATTENTION
Observe the displays on the display screen when switching on
the device.
Display of next service time for customer service
1
Battery charge display
2
E - Empty
F - Full
Operating hours display
3
English
General notes
Cleaning the device
Maintenance intervals
23

Publicidad

loading

Este manual también es adecuado para:

1.351-129.0