Publicidad
Idiomas disponibles
Idiomas disponibles
where a sudden slip could cause your hand to move
into the blade. Always make sure you have good
balance.
■
Allow the motor to come up to full speed before
starting a cut to avoid binding or stalling.
■
Do not use tool if switch does not turn it on
and off. Have defective switches replaced by an
authorised service centre.
■
Replacement parts. All repairs, whether electrical
or mechanical, should be made by a qualified
service technician at an authorised service centre.
■
When servicing use only identical replacement
parts. Use of any other parts may create a hazard or
cause product damage.
■
Keep hands away from cutting area. Do not hand
hold pieces so small that your fingers go under the
blade guard. Do not reach underneath work or in
blade cutting path with your hands and fingers for
any reason.
■
Never cut more than one piece at a time or stack
more than one workpiece on the saw table at a time.
■
Do not feed the material too quickly. Do not force
the workpiece against the blade.
■
Use only correct blades. Use the right blade size
and style for the material and the type of cut. Blade
teeth should point down toward the table.
■
Always support large workpieces while cutting to
minimize risk of blade pinching and kickback. Saw
may slip, walk or slide while cutting large or heavy
boards.
■
Do not remove jammed cutoff pieces until blade
has stopped.
■
Do not use saw bands which are damaged or
deformed.
■
Replace the table insert when worn.
■
Connect the product to a dust collecting device
when sawing wood.
■
Do not operate the product when the guard
protecting the saw band is open.
■
Select the saw band and the speed depending on
the material to be cut.
■
Do not clean the saw band whilst it is in motion.
■
Wear gloves when handling the saw band and
rough material.
■
Use a push stick when straight cutting small
work pieces using the fence.
■
Transport the product with the band guard fully
down and close to the table.
■
Place the fence on the lower side of the table
when bevel-cutting with the table inclined.
■
Use a suitable holding device when cutting
round or irregular shaped timber to prevent
twisting of the work piece.
■
Do not use guards for handling or transportation
■
Adjust the adjustable guard as close to the work
piece as practicable.
12
Original Instructions
■
Never touch blade or other moving parts during
use.
■
Before changing the setup and removing covers,
guards or blades, unplug the saw from the power
source.
■
Hold the workpiece firmly against the saw table.
■
To avoid accidental blade contact, minimize blade
breakage, and provide maximum blade support,
always adjust the blade guide assembly to just clear
the workpiece.
■
Keep blades clean, sharp, and with sufficient set.
Sharp blades minimize stalling and kickbacks.
■
Always turn off saw before disconnecting it to avoid
accidental starting when reconnecting to a power
source.
■
Make sure work area has ample lighting to see
the work and that no obstructions will interfere with
safe operation before performing any work using
your saw.
■
The blade guides have been preset at the factory.
These settings are functional for some applications.
We recommend that you check and adjust blade
guide settings before first use of your saw. Refer
to Adjusting thrust bearings and blade guide
support procedures explained in the Adjustments
section of this operator's manual.
■
Do not use tool to cut metal.
■
This tool should have the following markings:
●
wear eye protection.
●
keep fingers away from the blade.
●
do not remove jammed or cutoff pieces until the
blade has stopped.
●
be sure blade is installed with teeth pointing
down.
●
maintain proper adjustment of the blade tension,
blade guides, and thrust bearings.
●
adjust the upper guide to just clear the workpiece.
●
hold the workpiece firmly against the table when
cutting.
■
If the power supply cord is damaged, it must
be replaced only by the manufacturer or by an
authorised service centre to avoid risk.
■
Save these instructions. Refer to them frequently
and use them to instruct other users. If you loan
someone this tool, loan them these instructions also.
ELECTRICAL
EXTENSION CORDS
Use only 3-wire extension cords that have 3-prong
grounding plugs and 3-pole receptacles that accept
the product's plug. When using a power tool at a
considerable distance from the power source, use an
extension cord heavy enough to carry the current that
the product will draw. An undersized extension cord will
cause a drop in line voltage, resulting in a loss of power
and causing the motor to overheat.
Before using an extension cord, inspect it for loose or
Publicidad
