Publicidad
Idiomas disponibles
Idiomas disponibles
NOTE: Before performing any of the instructions throughout this manual, references to left,
right, front and rear of the tractor are from the operator's position, unless otherwise stated.
•
Before assembly, place the tractor on a firm, level surface, disengage the PTO, stop
the tractor engine and set the parking brake.
•
For convenience, pivot the seat forward and leave it in that position until the grass
collector is fully mounted and assembled.
Assemble Mounting Brackets
To assemble the universal mounting
assembly, locate the rider hitch bracket
assembly (689-00304A) and the universal
support bracket (783-08129) and follow
these steps:
1.
Attach the two hitch side brackets
to the rear support bracket
(rider hitch bracket assembly
689-00304A) using two carriage
bolts (710-0276) and wing knobs
(720-04122) from hardware pack
689-02364. See Figure 1.
NOTE: The hooks on the side
brackets should point downwards
and the tabs on the rear plate point
upwards as shown in Figure 1.
2.
Flip over assembly and mount the
hitch support bracket to the
universal support bracket (783-
08129) using two carriage bolts
(710-0276) and wing knobs (720-
04122) from hardware pack 689-
02364. See Figure 2.
NOTE: It might be easier during the mounting stage to leave this hardware only finger tight
to facilitate lining up the hitch hole for the clevis pin. You will be instructed to tighten this
hardware later in this manual.
NOTE: Use the two holes closest to the
cross mount, see Figure 2. The hitch
support bracket will need to be flipped to
enable alignment of the proper holes.
Mount Assembly on Tractor
1.
Place the hooked ends of the
mounting assembly over the
shoulder bolts on the back of the
tractor frame and line up the hitch
support bracket center hole with
the hole on the tractor's hitch. See
Figure 3.
2.
Install the clevis pin (711-0309A)
from hardware pack 689-02364
into the tractor's hitch and secure
with a cotter pin (714-0117).
See Figure 4.
ASSEMBLY AND INSTALLATION
Figure 1
For All Other Models
Knob Hole Position
Figure 2
Figure 3
Align hole on
bracket with hole
on tractor
Figure 4
NOTE: The clevis pin can be fed down through the hitch plate and secured underneath with
the cotter pin, or it may be easier to feed the clevis pin up through the hitch plate hole and
secure with the cotter pin on the topside. Insert the cotter pin into the top hole, closest to
the head of the pin. You may need to push up on the pin to make the hole accessible.
IMPORTANT ! If you decided to leave the
hitch support only finger tight during the
assembly process, tighten all of the
hardware securely at this time.
Mount Vertical
Support Bracket
1.
Install the vertical support bracket
onto the mounting assembly on the
tractor by hooking it over the cross
mounting bracket. See Figure 5.
2.
Align the vertical support bracket
with the hole that best suits the
deck size of your tractor.
3.
Secure the vertical support bracket
to the cross mounting bracket using
a carriage bolt (710-0276) and wing
knob (720-04122) from hardware
pack 689-02364. See Figure 6.
NOTE: Position "C" is the recommended
mounting position, but you may use other
mounting positions to accommodate
other attachments.
Install Hanger Assembly
1.
Install and secure hanger assembly
onto the vertical support bracket
using two carriage bolts (710-
0276), two cup washers (736-0242) and two lock nuts (712-04063) from hardware
pack 689-02364. See Figure 7.
Assembling Remaining Bagger Components
With the mounting brackets assembled and in place on the tractor, follow these steps to
assemble the remaining bagger components.
1.
Snap the upper chute support (731-17091)
in place by first clipping the side portion
onto the hanger assembly rail (1), as shown
in Figure 8.
2.
Snap the front side of the upper chute
support to the rail (2), as shown in Figure
8.
3.
If not already done so by the factory,
install the screen (731-06504) into
the bagger cover (631-04292) by first
inserting the end closest to the side with
the cut-out (1) into the mounting hole, as
in Figure 9.
4.
Make sure to feed the screen under the
lip. Clip in the other side by pushing the
screen into the provided cut-out (2). See
Figure 10.
6
38" Deck
42" Deck
46" Deck
A B C
Figure 5
Figure 6
Figure 7
.
Figure 8
1
Figure 9
Publicidad
