Screen Research XLR3 Manual De Instrucciones página 16

Fixed frame screen with masking installation and operation manual
Each programming procedure consists of several steps; at the end of each step, the operator has 60 seconds to start the next step; this system is devised to prevent the risk of performing operations other
than those desired. Therefore, if the motor does not perform the operation exactly as indicated in the instructions, wait 60 seconds, then exit programming, or cancel the procedure as indicated at specific
point, and start the procedure all over again.
Follow the table opposite to set formats of PILOT with the opening and
closing of the masking with print. Follow the table below to set the formats
with the MASTER remote control and saving it on PILOT, in line with the
transition number 6.
ENGINE 1 – ENGINE 3
The motor's settings follow an overwriting logic: therefore, once the end stop positions have been memorised they cannot be cancelled, but only overwritten by following the above-mentioned procedure from
the start.
In order to cancel the procedure in course, simultaneously press ■ and ▼ at any time, until the motor has executed 6 movements.
Made by Adeo Screen Sp. Z o.o. (Poland) Specifications are subject to change without notice. E&OE
Please verify that you are working with the latest revision of this document before specifying your screen.
Doc: XLR3 – Installation Manual rev5 | 20.11.2020
RATIO MEMORIZATION
Before start the programmation choose the engine you want to program with the number button, 1 – motor in the left side, 2 –
motor of the deco, 3 - motor in the right side.
Do the sequency below for each engine.
BOTTONS PILOT
Botton 1 of PILOT
Botton 2 of PILOT
Botton 3 of PILOT
Botton 4 of PILOT
Botton 5 of PILOT
Botton 6 of PILOT
Botton 7 of PILOT
Botton 8 of PILOT
Botton 9 of PILOT
ENGINE 1 – ENGINE 3
With the Master remote control and the ▲▼ ■
keys, bring both screens approximately to the
position that you intend to programme (to check the
exact size of the format required, we recommend
that you project some images of the relevant
format), then proceed as follows. Perform this
procedure up to 6 point with every single engine.
Press and release the button PRG, the engine
performs 2 movements.
Keep ▲ and ▼ keys simultaneously pressed until
the motor performs 2 movements
Note: at this stage, in order to perform precision
adjustments both the motors must be moved
exclusively with the ▲▼ keys. The remote control
will operate in a stuttering mode. In order to
perform millimetric adjustments press the ▲ or ▼
key briefly. To perform longer movements (but still
in a stuttering mode) keep the ▲ or ▼ key
pressed. Proceed in this manner to position the two
canvases exactly where you want to programme
them.
Once the required position is reached, keep the ■
key pressed until the motor has finished performing
3 movements.
Press a button (from 1 to 6) the button of the PILOT
remote control which you intend to associate to the
format, until each motor has finished performing 4
movements.
The required format is now memorized on the
Pilot remote control of your choice (1-6) and
the programming procedure is concluded.
MOVEMENT OF FORMAT
TO CANCEL THE PROGRAMMING IN COURSE
MASK POSITION DECO MASK
Aspect Ratio 1 In state "UP limit switch" (previous page)
Aspect Ratio 2 In state "UP limit switch" (previous page)
Aspect Ratio 3 In state "UP limit switch" (previous page)
Aspect Ratio 4 In state "UP limit switch" (previous page)
Aspect Ratio 5 In state "UP limit switch" (previous page)
Aspect Ratio 6 In state "UP limit switch" (previous page)
Aspect Ratio 7 In state "UP limit switch" (previous page)
Aspect Ratio 8 In state "UP limit switch" (previous page)
Aspect Ratio 9 In state "DOWN limit switch" (previous page)
ENGINE 1
ENGLISH
ENGINE 3
Page 16