Publicidad
Idiomas disponibles
Idiomas disponibles
CALIFORNIA PROPOSITION 65 WARNING
This product and related accessories contain chemi-
cals known to the State of California to cause cancer, birth defects
or other reproductive harm.
IMPORTANT: For best possible performance and continuous, satis-
factory operation, read these instructions before in stalling your new
pump. Should service be required, this manual can be a valuable
guide, it should be kept near the installation for ready reference.
INSTAllATION lOCATION
Place unit as close to water source as possible to mini mize suction
lift, obtain the best pumping performance, and aid in priming. A typi-
cal portable installation is shown in Figure 1.
For permanent installation, mount unit on a foundation that will sup-
port the weight of pump and engine and also provide stability while
the pump is running. For most per manent installations, it is advis-
able to bolt unit directly to foundation.
NOTICE: Settling and/or shifting during operation can cause piping
to place excessive strain on the pump and may damage pump case.
Set pump on hard level surface.
SuCTION CONNeCTION
Connect either rigid pipe or flexible suction hose to pump suction as
shown in Figure 1. If hose is selected, hose must be rated to hold
the suction pressure and prevent collapse while the pump is run-
ning.
Make the suction line a continuous rise from the water source to the
pump. High spots can trap air and also make priming difficult. Make
sure all connections are tight and free of air leaks.
NOTICE: Suction pipe or hose must be at least as large as the pump
suction inlet in order for the pump to operate properly.
Minimum depth for the suction inlet is determined by the diameter of
the suction line. See Figure 1.
NOTICE: Use a suction screen to keep debris out of pump.
Hazardous Suction.
Can trap persons
against suction inlet.
Always use strainer
on suction hose to
prevent entrapment.
Use pipe or reinforced hose to make
suction connection.
Hose must be strong enough to
not collapse during operation.
Suction screen area must be at least four
times suction pipe area.
All suction piping must slope up toward the
pump inlet.
Support the piping and fittings to reduce strain
on the pump case.
Priming Plug
Provide rigid
platform for pump.
Customer-supplied
Priming tee, plug
and nipple.
DISCHARGe CONNeCTIONS
Your pump is equipped with a single port discharge. Select the
appropriate size for the application. Install a "tee" as shown to allow
priming the pump without disconnecting the piping.
OPERATION
NOTICE: Do not start or run pump dry or damage to the mechani cal
seal will result.
NOTICE: Add engine oil before startup. Refer to the engine opera-
tion manual before startup.
PRImING THe PumP
A self priming pump only needs to be manually primed at the first
start-up. Once primed, under normal conditions the pump will re-
prime automatically at each subsequent start-up. If the pump is
used in portable applications and the water has been drained from
the pump case, re-prime before start-up.
To prime, remove plug from top discharge outlet and fill pump with
water. Replace plug and start pump. The pump will require a few
minutes to evacuate air from the suction line. After several minutes
of operation, pump will be fully primed and pumping water. Priming
time will vary depending on length and diameter of suction line.
RuNNING THe eNGINe
Refer to engine operation section of this manual for starting and
operating instructions.
Pump performance varies depending on engine RPM. Refer to
engine operation section to adjust engine speed.
Discharge pipe not
smaller than the pump
discharge opening.
(2" x 25' Discharge hose
included in kit FP2731)
Pump Inlet
Suction hose
(2" x 15' Suction hose
included in kit FP2735).
Support pipe and
fittings.
Strainer or foot valve
(2" strainer included
in kit FP2735)
Depth of suction inlet at least
four (4) times the diameter of suction
pipe to avoid forming vortexes.
Example:
2" Pipe x 4 = 8" minimum depth.
2
Figure 1 - Typical installation
Publicidad
