Publicidad
Idiomas disponibles
Idiomas disponibles
CAUTION:
1. When the tool is not in use, always switch off and
remove the battery cartridge from the tool.
2. Do not store the tool and battery cartridge in locations
where the temperature may reach or exceed 50°C
(122°F).
3. Do not give the tool a shock by dropping, striking, etc.
4. Do not expose the light to eyes continuously. It may
hurt them.
5. Do not cover or clog the lit tool with cloth or carton,
etc. Covering or clogging it may cause a flame.
6. Do not disassemble the charger or battery cartridge;
take it to a qualified serviceman when service or repair
is required. Incorrect reassembly may result in a risk
of electric shock or fire.
7. If any problem develops, consult your nearest Makita
Service Center or dealer. To maintain product safety
and reliability, repairs, maintenance or adjustment
should be carried out by Makita Authorized Service
Center.
The lamp was classified at risk Group 1.
a) The lamp or lamp system is in excess of the Exempt
Group and that the viewer-related risk is dependent
upon how the users install and use the product;
b) The most restrictive optical radiation hazard and other
optical radiation hazards in excess of Exempt Group.
c) Proper assembly, installation, maintenance and safe
use, including clear warnings concerning precautions
to avoid possible exposure to hazardous optical
radiation.
d) Advice on safe operation procedures and warnings
concerning reasonably foreseeable malpractices,
malfunctions and hazardous failure modes.
e) NOTICE: UV and IR emitted from this product.
f) WARNING: IR emitted from this product.
g) CAUTION: Possibly hazardous optical radiation
emitted from this product.
h) Minimise exposure to eyes or skin. Use appropriate
shielding.
i)
Use appropriate shielding or eye protection.
j)
Do not stare at operating lamp. May be harmful to the
eyes.
k) Eye or skin irritation may result from exposure. Avoid
eye exposure.
FUNCTIONAL DESCRIPTION
Charging (Fig. 1)
• Charge the battery cartridge with the Makita charger
before use.
• Use the battery cover to protect the battery terminals
from water or dust when the tool is not in use.
Installing or removing battery cartridge
(Fig. 2)
• To install the battery cartridge, align the tongue on the
battery cartridge with the groove in the housing and slip
it into place. Always insert it all the way until it locks in
place with a little click. If you can see the red indicator
on the upper side of the button, it is not locked
completely. Install it fully until the red indicator cannot
be seen. If not, it may accidentally fall out of the tool,
causing injury to you or someone around you.
• To remove the battery cartridge, slide it from the tool
while sliding the button on the front of the cartridge.
Battery protection system
The protection system is equipped, which automatically
cuts off the output power for its long service life. The light
goes off during operation when the remaining battery
capacity gets low. This is caused by the activation of
protection system and does not show the light trouble.
Remove the battery cartridge from the light and charge it.
Lighting up the LED light (Fig. 3)
Push the switch on the battery holder to light up the LED
light. To turn off, push the switch again.
Head angle (Fig. 4)
The head angle can be adjusted for every 15°.
Wearing flash light
Wear the flash light on your head using the head band to
secure it in place. (Fig. 5)
If the head band is too loose or too tight, adjust its length
with the band clips.
Slip the cord between the protrusions of the band clip to
keep it out of the way. (Fig. 6)
You can carry the battery holder on your waist belt using
the belt hook. (Fig. 7)
This flash light can be used as a stationary type light as
well. Install the flash light on the battery holder using the
front hook on the battery holder. (Fig. 8)
Do not remove the lamp cover to keep out the water.
The lamp shall not be repaired or replaced by the user.
If you remove the lamp cover accidentally, install it firmly
with rubber band.
MAINTENANCE
CAUTION:
• Always be sure that the tool is switched off and the
battery cartridge is removed before attempting to
perform inspection or maintenance except for the
following troubleshooting related to the light.
Tips for maintaining maximum battery life
1. Charge the battery cartridge before completely
discharged.
• Always stop tool operation and charge the battery
cartridge when you notice less tool power.
2. Never recharge a fully charged battery cartridge.
Overcharging shortens the battery service life.
3. Charge the battery cartridge with room temperature at
10°C - 40°C (50°F - 104°F).
• Let a hot battery cartridge cool down before
charging it.
4. Charge the battery cartridge once in every six months
if you do not use it for a long period of time.
Cleaning
From time to time wipe off the outside (tool body) of the
tool using a cloth dampened in soapy water.
CAUTION:
• Never use gasoline, benzine, thinner, alcohol or the
like. Discoloration, deformation or cracks may result.
7
Publicidad
