Corep LI181 Manual De Instrucciones página 3

Solar Motion Security LED Light
Introduction.
We congratulate you on the purchase of your LED Solar Sensor Light. You have chosen a high-quality product. Before using your LED Solar Sensor Light, please familiarize
yourself with the instructions and safety information below. Only use the product as described and for the specified applications.
This product is intended to illuminate outdoor areas for private use and is not suitable for commercial use or for use in other applications.
Attention: Connect solar panel with light, exposed solar panel under sunlight for 12 hours before first use.
Technical Data
Material: Aluminum+PC+ABS
LED Type: 50*2835
Battery: 1x7.4V, 1800mA (included)
Solar Panel: 12V 270mA 3.5W, size 150*200mm
Motion sensor angle: 180º
Detection range: Max.8-10m
Time setting: approx. 5s to 5min (+/-10%)
Lumen: 900LM (+/-10%)
Protection type: IP44 (splash-proof)
General safety instructions.
1. Children should not be allowed to play with the product. Cleaning and user maintenance should not be performed by children without adult supervision.
2. Never leave children unsupervised with the packaging material. The packaging material represents a danger of suffocation.
3. Do not use this product if you notice any damage
4. The light source contained in this luminaire shall only be replaced by the manufacturer or his service agent or a similar qualified person.
5. This appliance contains batteries that are only replaceable by skilled person.
Function
The LED light will switch on during twilight or darkness when the motion detector detects infrared radiation given off by people passing by.
User can turn the control knob TIME to adjust the duration of the illumination from approx. 3s to 7min (+/-10%).
User can turn the control knob SENS to adjust the range of the motion detector.
User can turn the control knob LUX to adjust the daylight level at which to activate the motion detector.
Note: Once the light is activated by the motion detector, any subsequent detection will restart the timed period again from the beginning.
Note: The motion detector responds to heat radiation. When outdoor temperatures are low, it is more sensitive to body heat than when outdoor temperatures are warm.
Note: If the light is not activating in nighttime, a street light, house light or other ambient light could be affecting activation. Turn the control knob LUX towards position
to increase the daylight level. If the light is unnecessarily activating in daytime, turn the control LUX towards position to decrease the daylight level.
Note: Regularly clean the motion detector to ensure proper functionality (refer to "Cleaning and Care ").
Installation
When selecting the exterior mounting location, pay attention to the following:
Note: The included mounting material is suitable for solid concrete or masonry construction. Other wall substrates may require additional fastening materials.
Note: An electric drill is required.
CAUTION! RISK OF INJURY! Please read the operating instructions for your drill.
CAUTION! Ensure that you do not damage any electrical cables in the wall or ceiling.
LED light installation
1. To choose the mounting location, make sure the LED light illuminates the desired area and that the LED Solar Sensor Light will not be directly exposed to rain.
2. Depending on the mounting height (roughly at 2m) the motion detector has a detection range of max. 8-10m with a detection angle of 180°.
3. Be sure the motion detector is not illuminated by street lighting at night. This can influence the motion sensor.
4. Loosen the screws on both sides of the bracket.
5. Select a location to attach the mounting bracket. Mark the elongated holes at the back of the bracket onto the mounting a surface. Using a drill bit, drill pilot holes for the
two mounting bracket screws at the locations established. Tighten the mounting screws down until secure.
6. When attaching the light head to mounting bracket, slip the light head between the sides of and align the mounting holes in the light head with the holes in the mounting
bracket. Be sure to place the washers between mounting holes on the security light and the mounting bracket. When the holes are aligned fasten the mounting bolts to
each side.
7. Rotate and adjust the LED light to illuminate the desired area.
8. Turn the control knob TIME to adjust the duration of the illumination. The lighting duration can be adjusted from approx. 5s to 5min (+/-10%).
9. Turn the control knob SENS to adjust the range of the motion detector. Mid position-normal setting, maximum position-maximum sensor's range 8-10m .
10. Turn the control knob LUX to adjust the daylight level: At the position , the motion detector only reacts at night.
In the position , the motion detector also responds at daylight levels.
Solar panel installation
1. To choose the mounting location, make sure the solar panel has direct and opulent sunshine and that the LED Solar Sensor Light will not be directly exposed to rain.
2. Use the holes on the mounting plate of solar panel intended for the screws to mark the positions for drilling.
3. Drill four holes in the mounting location, insert wall plugs and fix the solar panel with screws.
4. Rotate and adjust the solar panel to a position for direct sunlight.
5. Connect the solar panel and LED light by plugs on their cables.
6. After initial installation, the product needs about 12hours for charging under direct and opulent sunlight, before it can operate normally.