Infiniton FGC-117B Manual página 31

IV. Maintenance and cleaning
Before cleaning, unplug the power plug first; Do not plug in or plug out the plug with wet hand, because
there is a risk of electric shock and injury. Do not spill water directly on the refrigerator, to avoid rust, electricity
leakage and accidents. Do not stretch your hands into the bottom of the refrigerator, since you might be
scratched by sharp metal corners.
Internal cleaning and external cleaning
The food residuals in the refrigerator are liable to produce bad odor, so the refrigerator must be cleaned regularly. The
fresh food compartment is usually cleaned once a month.
Remove all shelves, crisper box, bottle racks, cover board, and drawers etc., and clean them with a soft towel or sponge
dipped in warm water or neutral detergent.
Clear off the dusts accumulated on the rear panel and side plates of the refrigerator often.
After using detergent, be sure to rinse it with clean water, and then wipe it dry.
Do not use bristle brush, steel wire brush, detergent, soap powder, alkaline detergent, benzene, gasoline,
acid, hot water and other corrosive or soluble items to cleanse the cabinet surface, door gasket, plastic
decorative parts, etc., so as to avoid damage.
Carefully wipe dry the door gasket, clean the groove using a wooden chopstick wrapped with cotton string. After the
cleaning, fix the four corners of the door gasket first, and then embed it segment by segment into the door groove.
Interruption of power supply or failure of the refrigerating system
•Take care of the frozen foods in the event of an extended non-running of the refrigerating appliance (such as interruption
of power supply or failure of the refrigerating system).
•Try to open the refrigerator door as less as possible, in this way can food safely and freshly kept for hours even in hot
summer.
•If you get the power outage notice in advance：
1) Adjust the thermostat knob to the high mode an hour in advance, so that foods get fully frozen (Do not store new
food during this time!). Restore the temperature mode to the original setting when power supply becomes normal in a
timely manner.
2) You can also make ice with a watertight container, and put it in the upper part of the freezer, so as to extend the time
for fresh food to be stored.
Note: Once the refrigerator is used, you'd better use it continuously; and under normal circumstance, do not
stop its use, so as not to affect the service life.
Defrosting
After a period of use, a thin layer of frost will be formed on the freezer compartment inner wall (or evaporator) surface,
which may affect the refrigeration effect if exceeding 5mm in thickness. In such case, you need to gently scrape the frost
off using an ice scraper rather than the metal or sharp hardware. Frosts need to be cleared off every 3 months or so, and if
the normal use of drawers and normal access of foods are affected by frosting, make sure to remove the frosts in a timely
manner. Follow the following steps to remove frosts:
1. Take out the frozen foods, shut off the mains power supply, open the refrigerator door, and gently remove the frosts
from the inner wall with an ice scraper. To speed up the thawing process, you are suggested to place a bowl of hot water
inside the refrigerator/freezer, and when the solid ice frosts become loose, use an ice scraper to scrape them off and then
take them out.
2. After defrosting, clean the refrigerator/freezer inside, and switch on the power supply.
Changing the lamp
The LED lamp is used by the refrigerator for lighting, which features low energy consumption and long service life. In case
of any abnormality, please contact the after-sales personnel for visiting service.The lamps can only be replaced by the
manufacturer,together with a part of the appliance.
Lamp type：LED light.
Safety-check after maintenance
Is the power cord broken or damaged?
Is the power plug firmly inserted into the socket?
Is the power plug abnormally overheat?
Note: Electric shock and fire accident may be caused in case the power cord and plugs damaged or stained
by dust. If any abnormality, please unplug the power plug and get in contact with the vendor.
V. Simple fault analysis and elimination
With regard to the following small faults, not every failure needs to be fixed by the technical service personnel; you can try
to solve the problem.
Case Inspection
 Is power plug off?
•
Completely
 Are breakers and fuses broken?
non-refrigeration
 No electricity or line trip?
Solutions
 Re-plug
 Opening the door and checking whether the lamp
is lit.
5