Producing Beat Effects - Pioneer DJM-700-S Manual De Instrucciones

EFFECT FUNCTIONS

PRODUCING BEAT EFFECTS

Beat effects allow the instant setting of effect times in synch with
the BPM (beats per minute), thus allowing the production of a
wide variety of effects in synch with the current rhythm, even
during live performances.
1 Set BPM measuring mode to AUTO to measure BPM (beats
per minute).
The BPM of the input music signal is detected automatically.
Whenever power is first turned ON, the function defaults to the
[AUTO] mode.
• In the event the track's BPM cannot be detected
automatically, the display's BPM counter will flash.
• Measurable range: BPM=70 to 180.
It may not be possible to measure some tracks
accurately.
In this case, press the TAP button and input the beat
manually.
[Using the TAP Button for Manual BPM Input]
If the TAP button is tapped two times or more in synch with
beat (1/4 notes), the BPM will be recorded as the average value
recorded during that interval.
• When BPM mode is set to [AUTO], tapping the TAP button
will cause the BPM mode to change to the TAP mode, and
the interval at which the TAP button is pressed will be
measured.
• When the BPM is set via the TAP button, the beat multiple
becomes "1/1" (or "4/1", depending on the effect selected),
and the time for 1 beat (1/4 notes) or 4 beats will be set as
the effect time.
• If the TIME dial is rotated while depressing the TAP button,
direct BPM can be set manually.
If the TIME dial is rotated while holding the TAP button and
AUTO buttons depressed, the BPM can be set in 0.1 units.
2 Set the effect selector to the desired effect.
• The display will show the name of the selected effect.
• See P. 16 to 17 for details regarding the various effects.
3 Set the effect channel selector to the channel you wish to
apply the effect to.
• The selected channel lights in the display's channel name
area.
• If [MIC] is selected, the effect will be applied to both
microphone 1 and microphone 2.
18
En
Display example
1 2 3 4
BEAT 2, 3
4
AUTO
TAP
TAP
1
AUTO
2
3
TIME
LEVEL/DEPTH
5 ON/OFF
4 Press the BEAT button ( ,
which the effect is to be synchronized.
• When
is doubled, and when
calculated from the BPM is halved (some effects also allow
"3/4" setting).
• The multiple of the selected beat (parameter 1 position) is
displayed in seven sections on the display (see P. 12).
• The effect time corresponding to the beat's multiple is set
automatically.
Example: When BPM = 120
1/1 = 500 ms
1/2 = 250 ms
2/1 = 1 000 ms
5 Set the ON/OFF button to ON to enable the effect.
• Each time the button is pressed, the effect alternates ON/
OFF (whenever power is first turned ON, the function
defaults to OFF).
• The ON/OFF button flashes when the effect is ON.
Parameter 1
Rotating the TIME (PARAMETER 1) dial adjusts the temporal
parameter (time) for the selected effect. (With some effects, this is
used for adjustments other than time parameters.)
See P. 20 for details regarding the effect on parameter 1 of rotating
the TIME (PARAMETER 1) dial.
Parameter 2
Rotating the LEVEL/DEPTH (PARAMETER 2) dial adjusts the
quantitative parameter for the selected effect.
See P. 20 for details regarding the effect on parameter 2 of rotating
the LEVEL/DEPTH (PARAMETER 2) dial.
Effect Name: DELAY
A B M
Effect Channel Select: CH 1
MIDI
BPM value: 120 BPM
BPM
%
Parameter 1: 500 ms
mS
Beat multiple: 1/1
) to select the beat multiple to
is pressed, the beat count calculated from the BPM
is pressed, the beat count