EINHELL TH-SS 405 EL Manual De Instrucciones Original página 21

5.3.2 Changing the blade (Fig. 1/3/7)
•
Open the clamping lever (14) and turn if ne-
cessary to release the blade.
•
Unscrew the left cover (4).
•
First take the blade out of the top blade hol-
der (13), pressing down the upper pendulum
arm as you do so.
•
Then take the blade out of the bottom blade
holder (8).
•
Pull the blade up and out through the table
insert (18).
•
Install the new blade in reverse order.
Caution: Always insert the blade so that the
teeth point toward the saw table.
The blade can be inserted in slot a or b;
Slot a: For cuts along the axis of the radial arm.
Slot b: For cuts across the axis of the radial arm.
Tension the blade by turning the clamping screw
(14) anticlockwise (right-hand thread).
5.3.3 Tilting the saw table (Fig. 8)
•
Undo the locking screw (5).
•
Tilt the table (7) to the left until the indicator
(17) points to the required angle value on the
scale (6).
Important: For precision work you should
fi rst carry out a trial cut and then re-adjust
the tilt angle as required.
6. Operation
6.1 Please note:
•
Your saw does not cut wood automatically.
For cutting to occur, you have to guide the
wood against the blade.
•
The teeth cut only on the down stroke of the
blade.
•
You have to guide the wood slowly against
the blade because the teeth are very small.
•
Every new user needs a certain training
period. You are certain to break a number of
blades at the beginning.
•
When cutting thick timber, be particularly
careful not to bend or twist the blade. This will
help to prolong blade life.
Anl_TH_SS_405_EL_SPK7.indb 21 Anl_TH_SS_405_EL_SPK7.indb 21
GB
6.2 On/Off switch (Fig. 3 / Item 2)
•
Press the green button to switch the saw on.
•
Press the red button to switch the machine
off.
•
Please note: The machine is equipped with a
safety switch to prevent it being switched on
again accidentally after a power failure.
6.3 Blade speed regulator (3)
The blade speed regulator allows you to set the
blade speed appropriate to the material to be cut.
6.4 Carrying out internal cuts
1. A feature of this fretsaw is that it allows you to
carry out internal cuts in a panel without
damaging it on the outside or circumference.
Warning! To avoid injury from accidental star-
ting: Before you remove or change the blade,
always set the switch to „0" position and pull
the power plug out of the socket.
2. To carry out internal cuts in a panel: Remove
the blade as described in Section 5.3.2
3. Drill a hole in the panel in question.
4. Place the panel on the saw table with the
drilled hole above the access hole.
5. Install the blade through the hole in the panel
and adjust the blade tension.
6. When you have completed the internal cuts,
remove the blade from the blade holders (as
described in Section 5.3.2) and take the pa-
nel off the table.
6.5 Adapter for jigsaw blades (Fig. 8/9)
•
Remove the saw blade as described in 5.3.2.
•
Now insert the fretsaw blade (Z) in the ad-
apter.
•
First remove the table insert (18).
•
Then hook both adapters (22) on the two saw
blade holders (8/13).
•
Insert the saw blade as described in 5.3.2.
6.6. LED lamp
This equipment comes with an LED lamp (26)
for additional illumination of the cutting area. The
lamp is mains-powered (no batteries required).
Ensure that there is suffi cient lighting in the wor-
king area further around.
- 21 -
18.04.13 13:19 18.04.13 13:19