LG WM3885H CA Serie Manual Del Propietário página 32

T RO U B L E S H O OT I N G
BEFORE CALLING FOR SERVICE
Problem
Water in the washer
drains slowly or not
at all, or the display
shows:
OE ERROR
NOT DRAINING.
CHECK THE DRAIN HOSE &
FILTER.
(LGUS)1-800-243 -0000
(LGCANADA)1-888-542-2623
Washer fills with
water slowly or not
at all, or the display
shows:
IE ERROR
NO WATER SUPPLY.
CHECK TAP & HOSE.
(LGUS)1-800-243- 0000
(LGCANADA)1-888-542-2623
Washer will not
turn on
Washer won't
spin, or the display
shows:
dE ERROR
THE DOOR IS OPEN.
PLEASE CLOSE THE DOOR
COMPLETELY.
(LGUS)1-800-243- 0000
(LGCANADA)1-888-542-2623
Door will not
unlock when cycle
is stopped or
paused
Wash cycle time is
longer than usual
Musty or mildewy
odor in washer
Steam is not visible
during STEAM cycle
32
(cont.)
Possible Causes
• Drain hose is bent, pinched,
or clogged.
• The drain filter is clogged.
• Water supply taps are not
open fully.
• Water line hoses are kinked,
pinched, or bent.
• Water inlet filters are clogged.
• Water pressure to tap or
house is too low.
• Power cord is not properly
plugged in.
• House fuse is blown, circuit
breaker has tripped, or power
outage has occurred.
• The door is not closed
properly.
• Interior temperature of washer
is too high.
• Water level in washer is
too high.
• The washer automatically
adjusts the wash time for
the amount of laundry, water
pressure, water temperature,
and other operating conditions.
• Incorrect or too much
detergent has been used.
• Inside of tub not cleaned
properly.
• This is normal.
Solutions
• Make sure the drain hose is free of clogs, kinks, etc.,
and is not pinched behind or under the washer.
• Clean the drain filter. See the Care and Cleaning
section.
• Make sure that the water taps are open fully.
• Make sure the hoses are not kinked or pinched. Be
careful when moving the washer.
• Clean the inlet filters. See the Care and Cleaning
section.
• Check another faucet in the house to make sure that
household water pressure is adequate.
• Make sure that the plug is plugged securely into a
grounded, 3-prong, 120-VAC, 60-Hz. outlet.
• Reset circuit breaker or replace fuse. Do not increase
fuse capacity. If the problem is a circuit overload,
have it corrected by a qualified electrician.
• Make sure that the door is closed properly and press
the START/PAUSE button. After starting a cycle, it
may take a few moments before the drum begins to
turn or spin. The washer will not spin unless the door
is locked (DOOR LOCK will appear in the display).
• If the door is closed and locked and the open door
error message is displayed, call for service.
• The washer door has a safety lock to prevent burns.
Allow the washer to cool until the DOOR LOCK
indicator turns off in the display.
• Allow the washer to complete the programmed cycle, or
select the Drain & Spin cycle (see the page 23 for details)
to drain the water.
• This is normal. The washer adjusts cycle time
automatically to provide optimal results for the
selected cycle.
• Use only HE (High-Efficiency) detergent in
accordance with the manufacturer's instructions.
• Run the TUB CLEAN cycle regularly. Be sure to
wipe around and under the door seal frequently.
• Because it uses pressurized steam, the washer
requires very small amounts of steam to achieve
optimal results. Excess steam could damage fabrics
and reduce efficiency.