Publicidad
Idiomas disponibles
Idiomas disponibles
ENGLISH
INTRODUCTION
This BACKEYE system has been designed to provide years of trouble-
free operation. Please read this manual thoroughly. This manual con-
tains instructions to make the installation of the camera and monitor
easier. This BACKEYE system is a supplement to standard rear-view
mirror systems, and will provide additional rear-view vision when
installed and maintained properly.
It is not intended in any way to be a substitute for careful and cautious
driving. All applicable traffic laws and motor safety regulations must
still be adhered to.
FEATURES
BE-900C CAMERA
• Auto White Balance (AWB)
•
Back Light Compensation (BLC)
• 320,000 pixel image sensor
• 6 Infra-Red LED
• Min 0.1 Lux sensitivity
• Automatic electronic iris provides a clearer, more consistent image
in low and bright light
• Wide-angle lens (130° Diag.) provides a broad viewing area
• Compact design and lightweight ease installation in most vehicles
• Waterproof Aluminum Die-Casting Housing
• Built-in microphone for audio pick up (See Fig. 6)
• Waterproof cable connection
• Fully Waterproof (IP67)
BE-100C CAMERA - Optional
• Auto White Balance (AWB)
• Back Light Compensation (BLC)
• 290,000 pixel image sensor
• 6 Infra-Red LED
• Min 0.5 Lux sensitivity
• Automatic electronic iris provides a clearer, more consistent image
in low and bright light
• Wide-angle lens (130° Diag.) provides a broad viewing area
• Compact design and lightweight ease installation in most vehicles
• Waterproof Aluminum Die-Casting Housing
• Built-in microphone for audio pick up (See Fig. 6)
• Waterproof cable connection
• Fully Waterproof (IP67)
BE-964M TFT LCD COLOUR 6.4" MONITOR
• FCC/CE/e-marking
• Day/night switch
• Brightness control
• Colour control
• Volume control
• Two camera inputs and Camera Selector Switch
• Power/stand-by switch
• Mirror/Normal selection switch
• Monitor pigtail:
Power socket
Camera 1 and Camera 2 input socket
CONTENTS OF 1 COMPLETE SYSTEM
BE-900C CCD CAMERA:
1-Camera
1-Camera bracket
4-Attachment screws with washers (M4 x 15)
1-Wind deflector
BE-964M MONITOR:
1-Monitor
1-Monitor bracket
BEFORE INSTALLATION
1. This system operates from 10 volts DC to 32 volts DC, negative
ground.
2. Please install this system according to the instructions in this manu-
al.
3. Do not disassemble the camera or the monitor. This voids the war-
ranty. Disassembling the camera will compromise the Waterproof
seal.
4. Connect the system to an ignition switched power source.
Connection to a battery source will reduce battery life.
WARNING
1. To prevent electrical shock, DO NOT OPEN THE MONITOR CASE.
There are potentially lethal voltages inside the monitor. There are no
user serviceable parts inside. If evidence of tampering is detected,
the warranty will be considered void.
2. Keep monitor away from leaking water, rain, moisture etc. It is NOT
waterproof. Any moisture inside the monitor could cause extensive
damage.
BE-964 BACKEYE REARVIEW CCTV SYSTEM
3. Use the self-tapping screws to mount the monitor to the dashboard
or headliner.
4. Do not cover air ducts. Monitor needs proper ventilation to prevent
overheating.
INSTALLATION INSTRUCTIONS
BE-900C CAMERA
1. Attach camera bracket (see Fig. 1) to upper portion of vehicle.
Attachment point must be sturdy enough to support camera and
bracket.
2. Attach camera to bracket using M4 bolts provided. Adjust angle as
indicated in Fig. 2. (Use rear bumper and back of vehicle as a refer-
ence point.)
3. Wind deflector may be installed. The deflector is designed to reduce
the build up of dust, dirt and moisture on the camera lens. (See
Fig.3.)
BE-964M MONITOR
1. Attach monitor inside vehicle in a location convenient to the driver
(e.g. centre of dash, overhead or in dash).
2. Use a compression plate to attach the monitor bracket to the dash
or overhead.
3. Adjust mounting angle of the monitor to allow driver to easily view
the screen from all seat positions. (See Fig. 4.)
CABLE
1. The camera to cable connection and the monitor pigtail are water-
proof. Be sure to position the cables properly.
2. Do not run the cable over sharp edges or corners. Do not kink the
cable. Keep the cable away from hot and rotating parts.
3. Place all excess cable in convoluted tubing.
4. Wire the cable securely.
WIRING CAMERA AND MONITOR
1. See wiring diagram for connections to ignition, ground and back up
circuit. (See Fig. 5.)
2. Wiring camera: Drill a 22mm - diameter hole into vehicle body near
the camera and bracket. Connect camera connector to extension
cable in vehicle. Push extra cable into vehicle (be careful not to kink
cable) and fit grommet into hole. Apply sealant around grommet to
increase resistance to water penetration.
3. Wiring monitor pigtail: Insert extension cable into camera 1 and
camera 2 position. Bundle excess cable together using a cable tie
or vinyl tape. This will avoid possible damage to cable during opera-
tion. (Fig. 5)
4. Wiring power cable: The red wire is connected to an ignition power
source, the black wire is connected to chassis ground, and the
green wire is connected to the vehicles reversing light circuit.
FUNCTIONS AND OPERATION
MONITOR
1. STANDBY LED. When the red LED is turned on, it indicates power
on.
When reverse gear is selected the images picked up by camera 1
will be shown on the monitor
2. POWER SWITCH. Press the power switch to turn the monitor on or
off.
3. CAMERA/AV SELECTOR. Depress the button to select the camera
(CA1, CA2) and also press the button to select the AV input signal.
4. NIGHT/DAY SWITCH. When viewing pictures at night or in a tunnel
change the picture brightness by pressing the night/day switch.
5. CAMERA SELECTOR. Depress the camera button to select the
camera connected to the camera 1. Press the camera button to
select the camera connected to the camera 2.
6. MONITOR PIGTAIL & EXTENSION CABLE
- POWER SOCKET
Insert the supplied power cable connector firmly until it is locked. To
remove the power connector, press in the clip and pull out the con-
nector, while holding the clip down.
- CAMERA INPUT SOCKET (CAMERA 1. CAMERA 2)
There are two Mini DIN type connectors for the video camera inputs.
7. VOLUME CONTROL . Adjust the volume control for the desired
sound level.
8. BRIGHT CONTROL. The brightness can be adjusted to suit settings
for "DAY/NIGHT".
9. COLOUR CONTROL. Adjust the colour control for the desired inten-
sity of colour.
10. TINT CONTROL (NTSC system only). Adjust the tint control for the
desired image's colour.
11. AUDIO/VIDEO OUTPUT JACK. Connect audio, video output con-
nector to a second monitor or VCR input with a RCA phone type
connector cable.
12. AUDIO/VIDEO INPUT JACK. For just monitoring on screen, put the
plug of A/V signal into this Jack.
13. MIRROR/NORMAL SELECTION SWITCH. When the switch is in MIR
position, the picture will show reverse image.
When the switch is in NOR position, the picture will show a normal
image.
*Camera 1 and Camera 2 are operated individually.
CAUTION
1. DO NOT OPEN THE CAMERA CASE. This will break the camera's
waterproof seal. If evidence of tampering is detected, the warranty
will be considered void.
2. Do not recommend mounting the camera near the lower area of the
vehicle (e.g. bumper). This reduces the view of the camera and
increases the chance of physical damage to the camera.
3. Use only the Inner Hexagonal screw and washers to mount the
camera.
MAINTENANCE
Remove dust and dirt with a damp soft cloth. Heavier dirt should be
removed with a damp soft cloth and mild detergent. Do not use strong
cleaning agents containing gasoline, thinner, benzene or alcohol. These
substances may damage the exterior surface of the monitor.
CAUTION
1. Before drilling, be sure no cable or wiring is on the other side. Be
sure to drill a 22mm diameter hole only.
2. Feed as much cable as possible into vehicle and clamp securely.
This reduces the possibility of it being hooked or snagged.
3. Keep all cables away from HOT, ROTATING and ELECTRICALLY
NOISY components.
4. To increase protection of cable, place all excess wire and extension
cable in convoluted tubing.
5. Do not twist camera cable and do not cut camera pigtail or cable.
SPECIFICATIONS
BE-900C CAMERA
VIDEO SYSTEM
NTSC/PAL
PICK-UP DEVICE
CCD
IMAGE SIZE
1/3 inch
SYNCHRONIZATION
INTERNAL
REQUIRED ILLUMINATION
0.1 Lux MINIMUM
VIDEO OUTPUT
1V (p-p), 75 ohm
OPERATING VOLTAGE
12Vdc
POWER CONSUMPTION
MAX 2.4W (AT 12 Vdc)
OPERATION TEMPERTURE
-30°C TO +50°C
WEIGHT
0.48Kg
DIMENSION (W x H x D) mm
69 x 41 x 59
BE-100C CAMERA - Optional
VIDEO SYSTEM
NTSC/PAL
PICK-UP DEVICE
CCD
IMAGE SIZE
1/3 inch
SYNCHRONIZATION
INTERNAL
REQUIRED ILLUMINATION
0.5 lux MINIMUM
VIDEO OUTPUT
1V (p-p), 75 ohm
OPERATING VOLTAGE
12 Vdc
POWER CONSUMPTION
MAX 2.4W (AT 12 Vdc)
OPERATION TEMPERTURE
-30°C TO +50°C
WEIGHT
0.25Kg
DIMENSION (W x H x D) mm
69 x 11 x 59
BE-964M MONITOR
VIDEO SYSTEM
NTSC/PAL
PICTURE TUBE
6.4 inch COLOUR TFT LCD SCREEN
PICTURE RESOLUTION
960(H) x 234(V)
AUDIO OUTPUT
0.5W (8 ohm)
POWER CONSUMPTION
MAX 5.4 Watts
OPERATION TEMPERTURE
-10°C TO + 60°C
OPERATION VOLTAGE
DC10 V TO DC32 V
WEIGHT APPROX.
460g
DIMENSION (W x H x D) mm
181 x 136 x 32
DISCLAIMER
The use of the BE-964 BACKEYE Observation system should not in any
way be used as a substitute for careful and cautious driving. Traffic
laws and motor safety regulations must always be adhered to.
Publicidad
