Descargar Imprimir esta página

TESY GCV11S 1504720 C21 TSRCP Instrucciones De Uso Y Mantenimiento página 17

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 27
S2 and an arrow pointing outwards from the serpentine
EN
lead-in – outlet of serpentine S2
There is a connexion with internal thread of ½" welded
to the water tank for the purposes of installing thermal
probe – marked with 'TS". The appliance is fitted with brass
pocket for a thermal probe which should be screwed into
the aforesaid connexion.
Technical parameters:
Type
Surface of serpentine S1 (m²)
Surface of serpentine S2 (m²)
Volume of serpentine S1 (l)
Volume of serpentine S2 (l)
Operational pressure of
serpentine S1 (MPa)
Operational pressure of serpen-
tine S2 (MPa)
Maximum temperature of heat
carrier (°C)
PERIODIC MAINTENANCE
IX.
Under normal use of the heater, under the influence
of high temperature, lime scale /the so-called lime
scale layer/ is deposited upon the heating element's
surface. This worsens the heat exchange between the
heating element and water. The heating element's
surface temperature increases along /of boiling
water/. The thermoregulator begins to switch on and
off more frequently. A ''deceptive" activation of the
thermal protection is possible. Due to these facts, the
manufacturer recommends preventive maintenance of
your water heater every two years by an authorized service
center or service base. This protective maintenance must
include cleaning and inspection of the anode protector
(for water heaters with glass-ceramic coating), which shall
be replace with a new one if need arises.
In order to clean the appliances use a damp cloth. Do not
clean with abrasive or solvent content detergents. Do not
pour water over the appliance.
The manufacturer does not bare the responsibility
for all consequences caused by not obeying the
instructions, given hereby.
Instructions for protecting the environment
Old electric appliances contain precious materials and
thus should not be thrown together with the household
litter. We kindly ask you make your active contribution
for protecting the resources and the environment by
handing over the appliance in the authorized buy-back
stations (if such exist).
14
Instructions for use and maintenance
GCV7/4S
GCV7/4S
GCV7/4S
10047
12047
15047
0.5
0.5
0.5
0.3
0.3
0.3
2.4
2.4
2.4
1.4
1.4
1.4
0.6
0.6
0.6
0.6
0.6
0.6
80
80
80
DESCRIPTION TO ANNEX I
(1) supplier's name or trade mark
(2) supplier's model identifier (3) the declared load
profile, expressed by the appropriate letter and typical usage in
accordance with Table 3 of Annex VII (4) the water heating
energy efficiency class of the model, determined in accordance
with point 1 of Annex II (5) the water heating energy efficiency in
%, rounded to the nearest integer (6) the annual electricity
consumption in kWh in terms of final energy and/or the annual
fuel consumption in GJ in terms of GCV, rounded to the nearest
integer and calculated in accordance with point 4 of Annex VIII
(7) the thermostat temperature settings of the water heater, as
placed on the market (8) the daily electricity consumption Q elec
in kWh, rounded to three decimal places (9) the declared load
profile, expressed by the appropriate letter in accordance with
Table 1 of this Annex (10) the mixed water at 40 °C V40 in litres,
rounded to the nearest integer;(11) maximum temperature of
the thermostat (12) 'out of the box-mode' is the standard
operating condition, setting or mode set by the manufacturer at
factory level, to be active immediately after the appliance
installation, suitable for normal use by the end-user according to
the water tapping pattern for which the product has been
designed and placed on the market (13) the water heating
energy efficiency in %, rounded to one decimal place (14) All
specific precautions for assembly, installation and maintenance
are described in the operating and installation instructions. Read
and follow the operating and installation instructions. (15) All of
the data that is included in the product information was
determined by applying the specifications of the relevant
European directives. Differences to product information listed
elsewhere may result in different test conditions. Only the data
that is contained in this product information is applicable and
valid.
DESCRIPTION TO ANNEX II
(1) supplier's name or trade mark
(2) supplier's model identifier (3) the energy efficiency
class of the model, determined in accordance with point 2 of
Annex II (4) the standing loss in W, rounded to the nearest
integer (5) the storage volume in litres, rounded to the nearest
integer (6) the storage volume V in litres, rounded to one decimal
place (7) the standing loss S in W, rounded to one decimal place
(8) all specific precautions for assembly, installation and
maintenance are described in the operating and installation
instructions. Read and follow the operating and installation
instructions. (9) all of the data that is included in the product
information was determined by applying the specifications of
the relevant European directives. Differences to product
information listed elsewhere may result in different test
conditions. Only the data that is contained in this product
information is applicable and valid.

Publicidad

loading