Publicidad
Downloaded by: pd-oliana on 07-03-2023 10:49 CET
58. Please don't cook the food directly on the tray / grid. Please put the food into or on appropriate tools
before putting them in the oven.
59. Hot surface, leave for cooling before closing the cover.
ELECTRICAL SAFETY
1. Plug the appliance in a grounded socket protected by a fuse conforming to the values specified in the techni-
cal specifications chart.
2. Have an authorized electrician set grounding equipment. Our company shall not be responsible for the dam-
ages that shall be incurred due to using the product without grounding according to local regulations.
3. The circuit breaker switches of the oven shall be placed so that end user can reach them when the oven
is installed.
4. The power supply cord (the cord with plug) shall not contact the hot parts of the appliance.
5. If the power supply cord (the cord with plug) is damaged, this cord shall be replaced by the manufacturer or
its service agent or an equally qualified personnel to prevent a hazardous situation.
6. Never wash the product by spraying or pouring water on it! There is a risk of electrocution.
7. WARNING: To avoid electric shock, ensure that the device circuit is open before changing the lamp.
8. WARNING: Cut off all supply circuit connections before accessing the terminals.
9. WARNING: If the surface is cracked, turn off the appliance to avoid risk of electric shock.
10. Do not use cut or damaged cords or extension cords other than the original cord.
11. Make sure that there is no liquid or humidity in the outlet where the product plug is installed.
12. The rear surface of the oven also heats up when the oven is operated. Electrical connections shall not
touch the rear surface, otherwise the connections may be damaged.
13. Do not tighten the connecting cables to the oven door and do not run them over hot surfaces. If the
cord melts, this may cause the oven to short circuit and even a fire.
14. Unplug the unit during installation, maintenance, cleaning and repair.
15. If the power supply cable is damaged, it must be replaced by its manufacturer or authorized technical
service or any other personnel qualified at the same level, in order to avoid any dangerous situation.
16. Make sure the plug is inserted firmly into wall socket to avoid sparks.
17. Do not use steam cleaners for cleaning the appliance, otherwise electric shock may occur.
18. An omnipolar switch capable to disconnect power supply is required for installation. Disconnection
from power supply shall be provided with a switch or an integrated fuse installed on fixed power supply
according to building code.
19. Appliance is equipped with a type ''Y'' cord cable.
20. Fixed connections shall be connected to a power supply enabling omnipolar disconnection. For applip -
ances with over voltage category below III, disconnection device shall be connected to fixed power supply
according to wiring code.
Gas Safety
1. This appliance is not connected to burning products evacuation apparatus.This appliance must be con-
nected and installed according to the installation regulations in force. Conditions regarding ventilation must be
considered.
2. When a gas cooking appliance is used; humidity, heat and burning products are generated in the room.
First of all, make sure the kitchen is well ventilated when operating the appliance and maintain natural
ventilation openings or install a mechanical ventilation equipment.
3. After using the appliance heavily for en extended period of time, additional ventilation may be required.
For example open a window or adjust a higher speed for mechanical ventilation, if any.
4. This appliance must be used only in well ventilated locations in accordance with the regulations in force.
Please read the manual before installing or using this product.
5. Before positioning the appliance, make sure local network conditions (gas type and gas pressure) meets
appliance requirements.
6. The mechanism cannot be run for longer than 15 seconds. If the burner is not on after 15 seconds, stop
the mechanism and wait for at least one minute before trying to ignite the burner again.
7. All kinds of operations to be performed on gas installation must be performed by authorized and
competent people.
8. This appliance is adjusted for natural gas (NG). If you have to use your product with a different gas type,
you have to apply to authorized service for the conversion.
9. For proper operation, hood, gas pipe and clamp should be replaced periodically accordint to manufacturer
recommendations and when required.
Publicidad
