Pentair ST.E.P. PLUS D Serie Manual Del Propietário página 2

Bomba sumergible
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Safety/Electrical
READ AND FOLLOW
SAFETY INSTRUCTIONS!
This is the safety alert symbol. When you see this symbol
on your pump or in this manual, look for one of the following
signal words and be alert to the potential for personal injury.
warns about hazards that will cause serious per-
sonal injury, death or major property damage if ignored.
warns about hazards that can cause serious per-
sonal injury, death or major property damage if ignored.
warns about hazards that will or can cause minor
personal injury or property damage if ignored.
The label NOTICE indicates special instructions which are
important but not related to hazards.
Carefully read and follow all safety instructions in this manual
and on pump.
California Proposition 65 Warning
This product and related accessories contain
chemicals known to the State of California to cause cancer,
birth defects or other reproductive harm.
Hazardous pressure. Under certain conditions,
submersible pumps can develop extremely high pressure.
Install a pressure relief valve capable of passing entire pump
flow at 75 PSI.
Do not allow pump, piping, or any other system compo-
nent containing water to freeze. Freezing may damage
system, leading to injury or flooding. Allowing pump or system
components to freeze will void warranty.
Hazardous voltage. Can shock, burn or cause
death. To avoid dangerous or fatal electric shock hazard, use
pump only in an effluent system. DO NOT install pump in an
open body of water ( a lake, swimming pool, etc.).
Install, ground and wire pump according to local and
Canadian Electrical Code or National Electrical Code
requirements that apply.
Disconnect electrical power supply before installing or
servicing pump.
Make sure pump nameplate voltage and frequency match
line voltage and frequency of power supply.
1. Install pump according to all plumbing, pump and well code
requirements.
2. Install an all leg disconnect switch in the power supply near
the pump.
3. Two-wire motors are equipped with automatic thermal
overload protection which will open the circuit and stop the
motor when a thermal overload (excessive heating) exists.
When motor cools, overload will rest and motor will restart
automatically. This can cause the pump to start unexpected-
ly and without warning.
GENERAL
Inspect pump for delivery damage. Report any damage to ship-
ping carrier or to factory immediately.
Have any installation, repair, or service work done by your deal-
er.
Never run pump dry.
During system operation, pump must be submerged at all times.
Pipe joint compound can cause cracking in plastics. Use only
PTFE pipe thread sealant tape when sealing joints in plastic
pipe or connecting pipe to thermoplastic pumps.
Warranty is void in the following conditions:
Water is highly corrosive.
If entrained gas or air present in water being pumped
reduce the flow and cause cavitation (which can damage
the pump).
Pump has been operated with discharge valve closed
(severe internal damage will result).
ELECTRICAL
Wiring/Grounding
Hazardous voltage. Can shock, burn, or cause
death. Permanently ground pump, motor and control box
before connecting power supply to motor.
Ground pump and motor in accordance with all codes and ordi-
nances that apply. All wiring must meet National Electrical Code
and Canadian Electrical Code (whichever applies). Use copper
ground wire at least as large as wires carrying current to pump.
Pump is supplied with copper ground wire. Use only copper wire
for connections to pump.
Permanently ground pump before connecting power cable to
power supply. Connect ground wire to approved ground first,
then connect to equipment being installed.
Do not ground to a gas supply line.
Float switches or any other approved motor control must match
motor input in full load amperes.
For more information, contact your local code officials.
Installation Wiring Instructions
Pump has two power supply wires (Red/Black) and one ground
wire (Green).
Fasten power supply wire leads securely to control panel; leave
4-5" of slack in leads at this point. Securely fasten leads to plas-
tic pipe within 6" of the pump discharge section.
NOTICE: To avoid dropping pump or damaging wires or splices,
NEVER allow pump wires to support weight of pump.
2

Publicidad

Tabla de contenido
loading

Tabla de contenido