Publicidad
Idiomas disponibles
Idiomas disponibles
•
Select magenta jet soap PrecisionSpray™ nozzle to
launch soap to second story siding and windows.
•
Select black fan soap PrecisionSpray™ nozzle for
general cleaning. Great for applying soap to
vehicles, boats, driveways, decks, and patios.
3.
Pull back on collar, insert new PrecisionSpray™ nozzle
and release collar. Tug on nozzle to make sure it is securely
in place.
Usage Tips
•
For most effective cleaning, keep PrecisionSpray™ nozzle
from 8 to 24 inches (20 to 61 cm) away from cleaning
surface.
•
If you get PrecisionSpray™ nozzle too close, especially
using a high pressure nozzle, you may damage surface
being cleaned.
•
DO NOT get closer than 6 inches (15 cm) when cleaning
tires.
2-IN-1 SIPHON SYSTEM
Cleaning and Applying Detergent with
the Project Pro
®
PerfectMix
Chemicals can cause bodily injury, and/or property
damage.
• NEVER use caustic liquid with pressure washer.
• Use ONLY pressure washer safe detergents/soaps. Follow all
manufacturers instructions.
To apply undiluted detergent using
the blue PerfectMix
siphon,
TM
follow these steps:
1. Review use of PrecisionSpray™ nozzles.
2. Attach PerfectMix™ siphon hose to
pump and PerfectMix™ concentrate
bottle.
3. Make sure fan soap (black) or jet soap
nozzle (magenta) is installed.
TM
Siphon
CAUTION
NOTE: Detergent cannot be applied with the high pressure
nozzles (Cyan, Orange or Red).
4.
Make sure garden hose is connected to water inlet.
Check that high pressure hose is connected to spray gun
and pump. Turn on water.
You must attach all hoses before you start the engine.
• Starting the engine without all the hoses connected and without
the water turned ON will damage the pump.
• Damage to equipment resulting from failure to follow this
instruction will void warranty.
5.
Start engine following instructions How to Start Your
Pressure Washer.
6.
Place threaded end of detergent siphoning tube into
detergent container. Tighten by hand.
7.
Apply detergent to a dry surface, starting at lower
portion of area to be washed and work upward, using
long, even, overlapping strokes.
8.
Allow detergent to "soak in" for 3-5 minutes before
washing and rinsing. Reapply as needed to prevent
surface from drying. DO NOT allow detergent to dry on
(prevents streaking).
Cleaning and Applying Detergent with
the Standard Clear Siphon
To apply diluted detergent using the
standard clear siphon tube,
follow these steps:
1.
Review use of
PrecisionSpray™ nozzles.
2.
Attach clear siphon hose to pump.
3.
Mix detergent solution as required by job.
4.
Place small filter end of clear siphoning tube into
container with diluted solution as described above.
Contact with the hot muffler can damage detergent
siphoning tube.
• When inserting the siphon into a detergent solution bottle,
route the tube so as to keep it from inadvertently contacting the
hot muffler.
NOTE: Make sure the filter is fully submerged in fluid while
applying solution.
5.
Make sure fan soap (black) or jet soap nozzle (magenta)
is installed.
NOTE: Detergent cannot be applied with the high pressure
nozzles (Cyan, Orange or Red).
6.
Make sure garden hose is connected to water inlet.
Check that high pressure hose is connected to spray gun
and pump. Turn on water.
7.
Start engine following instructions How to Start Your
Pressure Washer.
14
NOTICE
NOTICE
Publicidad
