Publicidad
Idiomas disponibles
Idiomas disponibles
- Check whether the moving parts function fault-
lessly and do not jam or whether parts are dam-
aged. All parts must be correctly mounted and
all conditions must be fulfilled to ensure fault-
free operation of the electric tool.
- Damaged protective devices and parts must be
properly repaired or replaced by a recognised
workshop, insofar as nothing different is speci-
fied in the operating manual.
- Damaged switches must be replaced at a cus-
tomer service workshop.
- Do not use any faulty or damaged connection
cables.
- Do not use any electric tool on which the switch
cannot be switched on and off.
15.
Have your electric tool repaired by a qualified
electrician
- This electric tool conforms to the applicable
safety regulations. Repairs may only be per-
formed by an electrician using original spare
parts. Otherwise accidents can occur.
16.
Attention!
- For your own safety, only use accessories and
additional equipment that are indicated in the
operating manual or have been recommended
or indicated by the manufacturer. Use of other
tools or accessories that those recommended
in the operating manual or in the catalogue
could represent a personal danger to you.
17.
Noise
- Wear hearing protection when using the com-
pressor.
18.
Replacing the connection line
- If the connection line is damaged, it must be re-
placed by the manufacturer or an electrician to
avoid danger. Danger due to electrical shocks.
19.
Filling tyres
- Check the tyre pressure immediately after filling
using a suitable pressure gauge, e.g. at a petrol
station.
20.
Street-legal compressors in construction site
operation
- Ensure that all hoses and fixtures are suitable
for the maximum permissible working pressure
of the compressor.
21.
Set-up location
- Only set up the compressor on a flat surface.
22.
In case of pressures above 7 bar, it is recom-
mended to equip supply hoses with a safety ca-
ble (e. g. a wire rope).
24 | GB
23.
Avoid over-stressing the piping system by using
flexible hose connections to prevent kinking.
24.
Use a residual current circuit breaker with a trig-
ger current of 30 mA or less. Using a fault-cur-
rent circuit breaker reduces the risk of an electric
shock.
ADDITIONAL SAFETY INSTRUCTIONS
Observe the corresponding operating manuals of
the respective compressed air tools / compressed
air attachments! The following general instructions
must also be observed:
Safety instructions for working with compressed
air and blasting guns
• Ensure there is sufficient distance to the product, at
least 2.50 m, and keep the compressed air tools /
compressed air attachments away from the com-
pressor during operation.
• The compressor pump and lines can become very
hot during operation. Touching these parts will burn
you.
• The air which is sucked in by the compressor must
be kept free of impurities that could cause fires or
explosions in the compressor pump.
• When releasing the hose coupling, hold the hose
coupling piece with your hand. This way, you can
protect yourself against injury from the rebounding
hose.
• Wear safety goggles when working with the blow-
out pistol. Foreign objects or blown off parts can
easily cause injuries.
• Wear safety goggles and a respirator when working
with the compressed air pistol. Dusts are harmful to
health! Foreign objects or blown off parts can easily
cause injuries.
• Do not blow at people with the blow-out pistol and
do not clean clothes while being worn. Risk of injury!
Safety instructions when using spraying attach-
ments (e.g. paint sprayers):
1.
Keep the spray attachment away from the com-
pressor when filling so that no liquid comes into
contact with the compressor.
2.
Never spray in the direction of the compressor
when using the spraying attachments (e.g. paint
sprayers). Moisture can lead to electrical hazards!
3.
Do not process any paints or solvents with a flash
point below 55° C. Risk of explosion!
4.
Do not heat up paints or solvents. Risk of explosion!
www.scheppach.com
Publicidad
