Publicidad
Idiomas disponibles
Idiomas disponibles
The Display
Warnings
The second line of the display also gives warnings and reminders:
(reminders occur at the end of the programme)
END OF CYCLE, EMPTY THE WATER BOTTLE
Reminder that the water container should be
emptied every time you use the dryer (see
Maintenance).
EMPTY WATER BOTTLE
Indicates that the water container is full. The
message will take a few seconds to go out after
replacing the empty water container; the dryer
must be running for this to happen (see The
Controls).
Note: If the water container fills and this message
is displayed, the heat is turned off and your
clothes will not dry.
Start and Programmes
Choosing a programme
1. Plug the dryer into the electrical socket.
2. Sort your laundry according to fabric type (see
Laundry).
3. Open the door and make sure the filter is clean
and in place and the water container is empty and
in place (see Maintenance).
4. Load the machine and make sure items are not
in the way of the door seal. Close the door.
5. If the display is not lit: Press the ON/OFF button
6. Press the Programmes Selection button that
corresponds with the type of fabric being dried by
checking the Programmes Table (see Programmes)
as well as the indications for each type of fabric (see
Laundry).
- If the Memory
Memo button is selected; steps 7, 8
and 9 are not required (see below).
7. Choose Timed Drying Temporizzato or Dryness
Levels Livelli Asciugatura option:
- If Timed Drying press and release the Timed
Temporizzato button until the required time is
displayed or...
- To change from default dryness setting, press and
release the Dryness Levels Livelli Asciugatura
button until required level is indicated.
! See Programmes Table, for more details.
Memory button:
Memo
First time you press this button the second line of the display will show PRESS AND HOLD TO STORE
After selecting your favorite programme and options you can save these settings by pressing and holding in the
Memory
Memo button for at least 5 seconds, the buzzer will then beep and the second line of the display shows
MEMORY . The next time you need this programme press the
button
and this programme will run.
If you wish, you can change your stored favorite, by selecting a new programme and/or options and press and hold
in the Memory
Memo button (as above).
CLEAN CONDENSER
This message indicates that you must clean the
Condenser unit (see Maintenance) and will occur
at intervals depending how much you have used
the dryer. When you finish the next programme the
message is cancelled.
CLEAN FILTER
Reminds you to clean the Filter every time you use
the dryer (see Maintenance).
8. Set a delay time and other options if necessary
(see The Display).
9. If you wish the buzzer to sound at the end of the
programme, press the Alarm Allarme button.
10. Press the Start/Pause Avvio/Pausa button
begin. The display will show the estimated time to end.
During the drying programme, you can check on
your laundry and take out items that are dry while
others continue drying. When you close the door
again, press the Start/Pause Avvio/Pausa button
in order to resume drying.
11. During the last few minutes of Drying Programmes,
before the programme is completed, the final COOL
TUMBLE phase
is entered (fabrics are cooled),
this phase should always be allowed to complete.
12. The buzzer (if Alarm Allarme option selected) will
warn you when the programme is complete and the
display shows END OF CYCLE, POST CARE PHASE
Open the door, take the laundry out, clean the filter
and replace it. Empty the Water Container and
replace it (see Maintenance).
If the Post Care Antipiega Post Asciugatura Option
has been selected and you do not remove the
laundry immediately, the dryer will tumble occasionally
for 10 hours or until you open the door.
13. Unplug the dryer.
Memo button, then the Start/Pause Avvio/Pausa
GB
to
25
Publicidad
