Descargar Imprimir esta página

Dexter 200SHS2.5 Manual De Instrucciones página 129

Lijadora orbital

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 21
FR
6. OPERATION
11.
11.
11.
ES
Sanding
PT
The sander can be used for most sanding operations on materials such as wood, plastic,
metal and painted surfaces.
IT
EL
FR
PL
5. BEFORE PUTTING THE EQUIPMENT INTO OPERATION
ES
RU
Where possible, secure smaller workpiece to prevent them from moving under the sander.
Lower the sander in contact with the workpiece without pressure and then start the sander.
PT
Grit
KZ
Move the sander slowly over the surface of the workpiece in a circular or curved motion with
60 or less
an even, moderate pressure.
IT
UA
If there are still scratches on your work after sanding, try either of the following:
80 – 100
- Go back to a coarser grit and sand the marks out before recommencing with the original
EL
RO
choice or,
120 – 150
- Try using new sanding sheet of the same grit to eliminate the unwanted marks before
180 – 220
PL
EN
240 or more
RU
Attaching sanding paper
7. MAINTENANCE
KZ
power point before making any adjustment.
Always disconnect the device before performing any adjustment or
UA
maintenance operation. If the supply cord is damaged, it must be replaced by
1.
Select the required grade of sanding paper.
the manufacturer or its service agent in order to avoid a hazard.
RO
2.
Remove any dust or debris from the hook and loop of the base.
Disconnect from the power supply immediately if the supply cord is damaged. Take
3.
To attach hook & loop type sanding paper simply align the holes in the sanding paper
care not to expose this tool to the rain.
EN
4.
To remove the sanding paper, peel it away from the base.
(always replace the two brushes at the same time)
5.
Ordinary (non Hook & Loop type) sanding paper can also be used.
6.
Release the sandpaper clamp from both sides of the sander.
Eric LEMOINE
Eric LEMOINE
Eric LEMOINE
7.
Insert the end of the sandpaper under one clamp and pull the paper tight over the base
Cleaning
ADEO Services 135 Rue Carnot — CS 00001 59790 RONCHIN — France (
ADEO Services 135 Rue Carnot — CS 00001 59790 RONCHIN — France (
ADEO Services 135 Rue Carnot — CS 00001 59790 RONCHIN — France (
ensuring the holes align with those in the base and then clamp the other side.
Avoid using solvents when cleaning plastic parts. Most plastic parts are susceptible to
8.
The sanding paper should be kept tightly clamped over the base, otherwise there could
damage from various types of commercial solvents and may be damaged by their use. Use
be excessive wear of the base material.
clean cloths to remove dirt, carbon dust, etc.
162
WARNING: Do not continue to use the sander with a sanding paper
that is overworn or damaged.
WARNING: Do not use the same sanding paper for wood and metal.
Metal particles become embedded in the sanding paper and will
ADEO Services
ADEO Services
ADEO Services
135 rue Sadi Carnot
135 rue Sadi Carnot
135 rue Sadi Carnot
CS 00001
CS 00001
CS 00001
59790 Ronchin - France (
59790 Ronchin - France (
59790 Ronchin - France (
WARNING : Don't use this machine on plaster.
,
,
,
Wear safety goggles and dust mask.
200SHS2.5
GRIT CHART
Type
Example of use
EC
EC
EC
Material removal, heavy paint removal,
Very Coarse
shaping wood
Paint removal, rough surface preparation
Coarse
(e.g. non-planed wood)
,
,
,
Medium
Surface preparation planed wood
Sanding between coats
Fine
EN 62841-1:2015
EN 62841-1:2015
EN 62841-1:2015
Very Fine
Final finishing
EN 62841-2-4: 2014
EN 62841-2-4: 2014
EN 62841-2-4: 2014
EN 55014-1:2017
EN 55014-1:2017
EN 55014-1:2017
EN 55014-2:2015
EN 55014-2:2015
EN 55014-2:2015
EN 61000-3-2:2014
EN 61000-3-2:2014
EN 61000-3-2:2014
EN 61000-3-3:2013
EN 61000-3-3:2013
EN 61000-3-3:2013
EN 50581 :2012
EN 50581 :2012
EN 50581 :2012
: .
: .
: .
)
)
)
:
:
:
200
200
200
200SHS2.5
200SHS2.5
,
,
,
2006/42/EC
2006/42/EC
2006/42/EC
2014/30/EU
2014/30/EU
2014/30/EU
2011/65/EU
2011/65/EU
2011/65/EU
(EU) 2015/863
(EU) 2015/863
(EU) 2015/863
:
:
:
.
.
.
CE: 19
CE: 19
CE: 19
Done in Ronchin : xx/xx/xxxx
Done in Ronchin : xx/xx/xxxx
Done in Ronchin : xx/xx/xxxx
FR
ES
PT
IT
EL
PL
:
:
:
RU
KZ
UA
RO
EN
)
)
)
117
FR
FR
FR
ES
ES
ES
PT
PT
PT
IT
IT
IT
EL
EL
EL
PL
PL
PL
RU
RU
RU
KZ
KZ
KZ
UA
UA
UA
RO
RO
RO
EN
EN
EN
117
117
129

Publicidad

loading