Narex EV 13 G-2 Instrucciones De Uso Originales página 18

English
3 Technical Specification
Model
Supply voltage (V)
Power frequency (Hz)
Power input (W)
Speed under load (rpm)
1st speed gear
2nd speed gear
Idle speed (rpm)
1st speed gear
2nd speed gear
Speed pre‑selection
Right‑left turning
Extent of chuck dia. (mm)
Thread on spindle
Quick‑tightening chuck Auto‑Lock
Drilling dia. max (mm)
into steel
into aluminium
into wood
Clamping neck dia. (mm)
Weight (kg)
Protection class
4 Machine Description
[1].....Chuck with ring gear
[2].....Spots on spindle
[3].....Clamping neck
[5].....Air vents
[6].....Latching pin
[7].....Switch / controller
[8].....Speed pre‑selection wheel
[9].....Alteration switch lever
[10] ..Gear‑shifting lever
[11] ..Additional handle
[12] ..Stop bar
[13] ..Chuck hook
[14] ..Spanner*
[15] ..Socket screw wrench*
[16] ..Quick‑tightening chuck
*) Some accessories displayed or described here may not be
included in the delivery.
5 Double insulation
To ensure maximum safety of the user, our tools are designed and
built to satisfy applicable European standards (EN standards). Tools
with double insulation are marked by the international symbol of
a double square. These tools must not be grounded and a two‑wire
cable is sufficient to supply them with power. Tools are shielded in
accordance with EN 55014.
6 Use
The machine is intended drilling in wood, metal, ceramic and plas‑
tic. Machines with electronic control and right/left rotation are also
suitable for screwing and thread cutting (Only for soft screwdriving
applications).
The user bears full responsibility for the consequences of using the
tool for purposes other than the above.
18
EV 13 G-2
0–1 750
0–1 100
0–3 050
1/2"–20 UNF
7 Commissioning
Any unauthorised use might cause damage to the tool. Therefore
follow these instructions:
– Always use sharp drill bits.
– Load the tool to avoid any significant reduction of speed or
stoppage.
– Always change the speed gear when the machine is idle or at
the machine slow‑down at low speed, in no case during the
drilling or when the machine is otherwise loaded.
Check that the information on the production plate matches the
real voltage of the power source.
Check that plug matches the type of socket.
Tools designed for 230 V can also be connected to 220/240 V.
ATTENTION!
Noise is generated during work!
Use ear protection!
7.1 Additional handle SOFTGRIP
For safety reasons always use the additional handle [11], firmly
mounted on the clamping neck [3]. The stop bar [12] can be used
to adjust the drilling depth. By rotating the handle the position of
the addition al handle and the depth stop can be modified.
7.2 Clamping of drill bits
Chuck with ring gear
Open the chuck to allow mounting of the tool. Mount the tool on.
Mount the tool on and, using the chuck hook [13] clamp in evenly.
Quick-tightening chuck
Open the chuck to allow mounting of the tool. Mount the tool on.
Tighten the quick‑tightening chuck by your hand so strongly that
a "click" sound is heard clearly. Thus the chuck will be secured
automatically.
This lock will release again if you turn the sleeve contra direction‑
ally to remove the tool.
Be careful as the chuck gets hot:
In case of longer work tasks, especially in impact drill-
ing, the chick might get very hot. In this case you are
recommended to wear protective gloves.
EV 13 G-2A
230 230
50–60 50–60
760 760
0–600 0–600
0–1 750
0–1 100
0–3 050
 
 
1.5–13 1.5–13
1/2"–20 UNF
û 
13 13
25 16
45 45
43 43
2.0 2.1
II / II /