Descargar Imprimir esta página

Craftsman 917.386082 Manual De Instrucciones página 10

Publicidad

Idiomas disponibles

Idiomas disponibles

The
operation
of any lawn
mower
can result in foreign
objects
thrown
into the
eyes, which can result in
severe
eye damage.
Always
wear safety glasses
or eye
shields
while operating
your
lawn mower
or performing
any adjustments
or repairs.
We recommend
a standard
safety
glasses
or wide vision safety mask worn
over spectacles.
ENGINE
SPEED
The engine speed was set at the factory
for optimum performance.
Speed is not
adjustable.
ENGINE ZONE CONTROL
ACAUTION:
Federal
regulations
require
an engine control
to be installed
on this
lawn mower in order to minimize
the risk
of blade contact
injury. Do not under any
circumstances
attempt to defeat the
function
of the operator
control.
The blade
tums when the engine
is running.
• Your lawn mower
is equipped
with an
operator
presence
control
bar which
requires
the operator
to be positioned
behind the lawn mower
handle to start
and operate
the lawn mower.
TO ADJUST
CUTTING
HEIGHT
Raise wheels for low cut and lower
wheels for high cut, adjust cutting height
to suit your requirements.
Medium
position is best for most lawns.
To change cutting height, squeeze
adjuster lever toward wheel.
Move
wheel up or down to suit your require-
ments. Be sure all wheels are in the
same setting.
NOTE:
Adjuster
is properly
positioned
when plate tab inserts
into hole in lever.
Also, 9-position
adjusters
(if so equipped)
allow lever to be positioned
between
the
plate tabs.
LOWER WHEELS FOR HIGH CUT
Plate tal
RAISE WHEELS FOR LOW CUT
Lever
BEFORE STARTING
ENGINE
ADD OIL
Your lawnmower
is shipped without oil in
the engine. For type and grade of oil to
use, see "ENGINE"
in the Maintenance
section of this manual.
A CAUTION:
DO NOT overfill engine with
oil, or it will smoke on startup.
1. Be sure lawnmower
is level and area
around oil fill is clean.
2.
Remove oil dipstick from oil fill spout.
Make sure that rim of spout is clean.
3. You receive a container of oil with the
unit. Slowly pour 3/4 (15 oz.) of the oil
from the container down the oil fill
spout into the engine.
4. Wait one minute to allow oil to settle.
Insert and tighten dipstick, then
remove it to check oil level.
5. Continue adding small amounts of oil
and rechecking the dipstick until it
reads full. DO NOT overfill, or engine
will smoke on startup.
6. Always be sure to retighten oil dipstick
before
starting
engine.
• Check oil level before
each use.
Add
oil if needed.
Fill to full line on dipstick.
• Change
the oil after every 25 hours of
operation
or each season.
You may
need to change
the oil more often
under dusty,
dirty conditions.
ADD GASOLINE
• Fill fuel tank to bottom
of tank filler
neck.
Do not overfill.
Use fresh, clean,
regular
unleaded
gasoline
with a
minimum
of 87 octane.
Do not mix oil
with gasoline.
Purchase
fuel in
quantities
that can be used within 30
days to assure fuel freshness.
_1, CAUTION:
Wipe off any spilled oil or
fuel.
Do not store, spill or use gasoline
near an open flame.
_, CAUTION:
Alcohol
blended
fuels
(called
gasohol
or using ethanol
or
methanol)
can attract moisture
which
leads to separation
and formation
of
acids during storage.
Acidic gas can
damage
the fuel system
of an engine
while in storage.
To avoid engine
problems,
the fuel system
should
be
emptied
before storage
of 30 days or
longer.
Drain the gas tank, start the
engine
and let it run until the fuel lines
and carburetor
are empty.
Use fresh fuel
next season.
See Storage
Instructions
for
additional
information.
Never use engine
or carburetor
cleaner
products
in the fuel
tank or permanent
damage
may occur.
10

Publicidad

loading