Bosch Professional GHO 26-82 D Instrucciones De Servicio página 19

23 Locking nut for adjustment of rebating width
24 Fastening bolt for parallel and beveling guide
25 Angle stop*
26 Locking nut for angle adjustment
27 Fastening bolt for rebating depth stop
28 Rebating depth stop*
29 Park rest
Technical Data
Planer
Article number
Rated power input
No-load speed 127 V
220 V
Planning depth
Rebating depth
Planing width, max.
Weight according to EPTA-Procedure 01/2003*
Protection class
* Including accesories
The values given are valid for a nominal voltage [U] of 220V - 230 V. For different voltages and models for specific countries, these values can vary.
Please observe the article number on the type plate of your machine.
The trade names of the individual machines may vary.
Noise/Vibration Information
Measured sound values determined according to EN
60745.
Typically the A-weighted noise levels of the product are:
Sound pressure level 83 dB(A); Sound power level 94
dB(A).
Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values ah (triax vector sum) and uncertainty
K determined according to EN 60745:
2 2
ah=2,1m/s , K=1.5 m/s .
The vibration emission level given in this information sheet
has been measured in accordance with a standardised test
given in EN 60745 and may be used to compare one tool
with another. It may be used for a preliminary assessment
of exposure.
The declared vibration emission level represents the main
applications of the tool. However if the tool is used for
different applications, with different accessories or poorly
maintained, the vibration emission may differ. This may
significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should
also take into account the times when the tool is switched
off or when it is running but not actually doing the job. This
may significantly reduce the exposure level over the total
working period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and
the accessories, keep hands warm, organise work patterns.
2 609 141 204 | 05.2015
Manual GHO 26-82 D Professional.indd 19
30 Drive belt
31 Large pulley
32 Small pulley
33 Chip/dust bag*
*Accessories shown or described are not part of the standard
delivery scope of the product. A complete overview of
accessories can be found in our accessories program.
W
-1
min
mm
mm
mm
Kg
Assembly
u Before any work on the machine itself, pull the
mains plug.
Changing the Tool
u Be cautious when replacing the planer blades. Do
not grasp the planer blades by the cutting edges.
Possible danger of injury due to the sharp cutting edges
of the planer blades.
Disassembling the Planer Blade(s)
(see figures A—C)
To reverse the planer blades, rotate the blade drum 14
until the clamping jaw 13 is parallel to the planer base
plate 6.
– Unscrew the 3 fastening screws 12 with the Torx key
11 and remove the clamping jaw 13.
– Slide the planer-blade retainer 17 together with the
planer blade 16 out of the guide groove 15 of the blade
drum 14.
– Turn the blade drum by 180° and disassemble the 2nd
planer blade.
Note: Before replacing or resharpening the planer blades,
remove the HSS planer-blade retainer 17 by loosening the
fastening screws 18.
Resharpening HSS Planer Blades (see figure D)
Worn or dull HSS planer blades can be resharpened with
the sharpening device 19 (accessory) and a commercially
available whetstone.
19
English |
GHO 26-82 D
Professional
3 601 EA4 3...
710
16500
18000
0–2,6
0–9
82
3,8
/ II
Bosch Power Tools
20/05/15 09:04