Kärcher VC 4 Cordless myHome Manual Del Usuario página 19

Cleaning the multi-function nozzle
1. Switch off the device.
2. Remove accessories.
ATTENTION
Short circuit hazard
The multi-function brush contains electrical compo-
nents.
You must not immerse the multi-function brush in water
or clean it with a damp cloth.
3. Clean the multi-function brush.
a Unlock the brush roll cover / support with a coin
or other object and remove it.
Illustration V
b Remove the brush roll from the brush opening in
the direction of the arrow.
Illustration W
c Remove the dirt e.g. with a brush. Any tangled
threads or hairs can be carefully cut off with scis-
sors.
d Carefully clean the brush opening with a cloth or
soft brush.
Illustration X
e Insert the brush roll into the brush opening.
f Lock the brush roll with a coin or other object.
Illustration Y
Cleaning the mini turbo nozzle
1. Switch off the device.
2. Remove accessories.
ATTENTION
Short circuit hazard
The mini turbo nozzle contains electrical components.
Do not immerse the mini turbo nozzle in water or clean
it with water.
3. Clean the mini turbo nozzle.
a Press down the brush roller cover and remove
the brush roller.
Illustration Z
b Remove residue, e.g. with a brush. Any tangled
threads or hairs can be carefully cut off with scis-
sors.
c Carefully clean the brush opening with a cloth or
soft brush.
Illustration AA
d Diagonally insert the brush roller fully into the
brush opening, pressing upwards until the cover
has clicked into place.
Illustration AB
Troubleshooting guide
Malfunctions often have simple causes that you can
remedy yourself using the following overview. When in
doubt, or in the case of malfunctions not mentioned
here, please contact your authorised Customer Service.
The device does not start up
Battery is empty.
 Charge the rechargeable battery.
Battery is not inserted correctly.
 Push the battery into the mount until it locks into
place.
Battery is defective.
 Replace the battery.
The battery is not charging
The charging plug/mains plug is not connected correct-
ly.
 Connect the charging plug/mains plug correctly.
The socket is defective.
 Check that the socket is working.
The wrong charger is being used
 Check that the correct charger is being used.
The device stops during operation or the suction
performance is poor
The battery has overheated.
 Stop work and wait until the battery temperature is
back in the normal range.
The accessories, the suction opening on the dust con-
tainer or the suction pipes are clogged.
 Remove the clog with a suitable aid.
The dust container is full.
 Empty the dust container.
The filters are soiled.
 Clean the filters, see chapter Care and service.
Roller brush is blocked.
 Remove any blockage.
Abnormal engine noise
The accessories, the suction opening on the dust con-
tainer or the suction pipes are clogged.
 Remove the clog with a suitable aid.
Removing and installing the battery
ATTENTION
Frequent removal of the battery
Frequent removal of the battery can damage the bat-
tery.
Only remove the battery for maintenance
and care if the device is not used for a long period of
time or if the device has to be sent for servicing.
Removing the battery
1. Press the unlocking button.
2. Remove the battery from the device.
Illustration AC
Inserting the battery
ATTENTION
Dirty contacts
Damage to the device and battery
Check the battery mount and the contacts for soiling
and clean them as necessary before inserting the bat-
tery.
Note
Use only fully charged batteries.
1. Push the battery into the mounting in the device until
it audibly latches into place.
Illustration AD
Technical data
Electrical connection
Voltage of charger
Nominal power
Battery pack type
Charger
Model
Part number
Nominal voltage of charger
Frequency
English
V 21,6
W 140
Li-ION
26 V
TEK
YLJXA-
T260040
6.198-
005.0
V 100 -
240
Hz 50 - 60
19