Publicidad
Idiomas disponibles
Idiomas disponibles
IMPORTANT
Please read
these
instructions carefully before you start to assemble this carport.
Please
carry
out the
steps
in
the order
set
out
in
these instructions.
Keep these
instructions
in
a
safe
place
for future
reference.
»
Care
and Safety advice
Please
follow
the instructions
as
listed
in
this manual.
Sort the parts and check against the
content
list.
For
safety purposes we
strongly recommend that the product to
be
assembled
by at least
two
people.
Some parts have metal edges.
Please be
careful when handling components.
Always wear gloves, shoes and safety goggles during assembly.
Do
not attempt to
assemble the carport
in
windy
or
wet conditions.
Dispose
of
all
plastic bags safely
-
keep
them out of
reach
of
small
children.
Keep
children away from the assembly
area.
Do
not attempt to
assemble the carport
if
you
are
tired,
have
taken drugs,
medications
or alcohol, or
if
you
are
prone to dizzy
spells.
When using
a
stepladder
or
power tools, make
sure
that
you
follow
the
manufacturer's safety advice.
Do
not climb
or stand on the roof.
Heavy
articles should not
be
leaned against the poles.
Please
consult your
local
authorities if
any
permits
are
required.
This
product
is
specifically designed
with
a
minor
slope
of
the roof
in
order to allow
drainage of water flow.
Please
keep
roof
and
gutters
clear
of
snow,
dirt
& leaves.
Heavy
amounts of snow
on
roof
can
damage the carport, making it unsafe to
stand
below
or nearby.
This
product
was
designed and produced to
be used
mainly
as
a
carport.
If color
was
scratched
during
assembly it
can be
fixed.
»
Cleaning instructions
When
your carport
needs cleaning,
use
a
mild detergent solution
and rinse
with
cold clean water.
Do
not
use
acetone, abrasive cleaners, or others special detergents to clean the panel.
Before
Starting Assembly
This
carport must
be
assembled on
a
solid
base (such
as
concrete or asphalt).
Choose
your
site
carefully before beginning assembly.
Site
surface (mainly below poles)
needs
to
be level.
During assembly
use
a
sof
platform below the
parts to avoid scratches and damages.
T001
»
During Assembly
When
encountering the information
icon, please refer
to the relevant
assembly step for additional comments and assistance.
Please
note you install the panels
with
the
UV
protected
side
out
(marked
with
"THIS
SIDE
OUT") and peel
the film strip covering the
panels.
Step
5: It
is
recommended to
place
a
sheet
/
Carton
below the parts to avoid
scratches and peeling
of
paint.
Step 5-6: According to the desired drainage direction,
please select
the preferred
side
to
place
the shorter
legs. Please
verify both
legs
#8002
are
mounted
on
the
same side
Step
7:
At the end
of
this
step,
tighten
all screws in
the carport.
Step
14: Perform
gradually
in
accordance
with the previous
steps
Step
17: Carefully
apply silicone sealant along the inner cross-section of parts
#7039 & 8119.
Step 21:
Make sure parts
#7580 (Step
18) are placed
underneath
each
and every
panel
(supporting the panels'edges).
Step 23:
Level
the poles with the foot-pads
on
to the flat
surface, and
then attach
to the
surface
of your choosing
using accordant screws and anchors.
Tighten
all screws
at the end
of
assembly.
E
co
co
.263
de.
331
e.
Do
not tighten
screws and nuts (8192 & 466)
until completion of assembly
process.
These
2
icons
indicate if screws'tightening
is
required or not.
Publicidad
