Publicidad
Idiomas disponibles
Idiomas disponibles
LAWN MOWER
Alwaysobservesafety ruleswhen per-
formingany maintenance.
TIRES
• Keep tires free of gasoline,
oil, or insect
control chemicals
which can harm rubber.
• Avoid
stumps,
stones,
deep ruts, sharp
objects
and other
hazards
that may
cause tire damage.
DRIVE
WHEELS
Check front drive wheels
each time before
you mow to be sure they move freely.
The wheels
not turning
freely means
trash,
grass cuttings,
etc. are in the drive wheel
area and must be cleaned
to free drive
wheels.
If necessary
to clean the drive wheels,
be
sure to clean both front wheels.
1.
Remove
hubcaps,
Iocknuts
& washers.
2.
Remove
wheels
from wheel
adjusters.
3.
Remove
any trash or grass cuttings
from inside the dust cover, pinion and/
or drive wheel gear teeth.
4.
Put wheels
back in place.
NOTE:
If after cleaning,
the drive wheels
do not turn freely,
contact
a Husqvarna
or
other qualified
service
center.
BLADE
CARE
For best results,
blade must be kept
sharp.
Replace
a bent or damaged
blade.
CAUTION:
Use only a replacement
blade approved
by the manufacturer
of
your mower.
Using a blade not approved
by the manufacturer
of your mower
is haz-
ardous,
could damage
your mower
and
void your warranty.
TO REMOVE
BLADE
1.
Disconnect
spark plug wire from spark
plug and place wire where
it cannot
come
in contact
with plug.
2.
Turn lawn mower on its side. Make
sure air filter and carburetor
are up.
3.
Use a wood
block between
blade and
mower
housing
to prevent
blade from
turning
when
removing
blade bolt.
NOTE:
Protect
your hands with gloves
and/or wrap blade with heavy cloth.
4.
Remove
blade
bolt by turning
counter-
clockwise.
5.
Remove
blade & attaching
hardware
(bolt, lock washer
& hardened
washer).
13
Blade adapter
Lockwasher
_
Blade
\
bolt
Hardened
washer
Key
_-
,/
(
Crankshaft
Crankshaft
TO REPLACE
BLADE
1. Position
blade on the blade adapter
aligning
the two (2) holes in the blade
with the raised
lugs on the adapter.
2.
Be sure the trailing
edge of blade (op-
posite sharp edge) is up toward
the
engine.
3.
Install the blade bolt with the lock
washer
and hardened
washer
into
blade adapter
and crankshaft.
4.
Use block of wood
between
blade and
lawn mower
housing
and tighten
the
blade bolt, turning
clockwise.
Recommendedtighteningtorque:35-40ft.lbs.
IMPORTANT:
Blade bolt is heat treated.
If bolt needs
replacing,
replace
only with
approved
bolt shown
in the Repair
Parts
section
of this manual.
TO SHARPEN
BLADE
NOTE:
We do not recommend
sharp-
ening the blade - but if you do, be sure the
blade is balanced.
Care should
be taken
to keep the blade balanced.
An unbal-
anced
blade will cause eventual
damage
to mower or engine.
• The blade can be sharpened
with a file
or on a grinding
wheel.
Do not attempt
to sharpen
while on the mower.
• To check blade balance,
drive a nail into
a beam or wall. Leave
about one inch of
the straight
nail exposed.
Place center
hole of blade over the head of the nail.
If blade is balanced,
it should
remain
in
a horizontal
position.
If either end of the
blade moves
downward,
sharpen
the
heavy end until the blade is balanced.
GRASS
CATCHER
• The grass catcher
may be hosed with
water,
but must be dry when used.
• Check your grass catcher
often for dam-
age or deterioration.
Through
normal
use it will wear.
If catcher
needs
replac-
ing, replace
only with approved
replace-
ment catcher
shown
in the Repair
Parts
section
of this manual.
Give the lawn
mower model
number
when ordering.
Publicidad
