CAME GROUP BPT Futura X1 Manual Del Usuario página 7

English
General Notes
• Read the instructions carefully before beginning the installation and carry
out the actions as specified by the maker;
• The installation, programming, commissioning and maintenance of the
product must be carried out only by qualified technical personnel, correctly
trained with regard to respecting the regulations in force, including the im-
plementation of accident prevention measures and the disposal of packaging;
• Before carrying out any cleaning or maintenance operation, disconnect
the device from the power supply;
• The equipment must be destined solely for the use for which it was
expressly designed;
• The manufacturer declines all liability for any damage as a result of
improper, incorrect or unreasonable use.
Wall-mounted installation
Unfasten the equipment from the metal support by letting it run smoothly
along it after you have pressed the plastic catch A.
Fix the metal support to the round Ø 60 mm back-box B or the rectangular
503 back-box CD using the screws provided and paying attention to the
(TOP) direction indication. The box must be installed at an appropriate
height for the user. Avoid tightening the screws too much.
Once the connections are made, hook the video terminal onto the metal
support EF.To unhook the unit from the metal support press the plastic
catch and lift the terminal G.
For recessed installation refer to the recessing kit manual.
Technical Features
Type
Power supply by BUS (VDC)
Consumption (mA max)
Consumption in stand by (mA)
Local power supply (VDC)
Consumption (mA max)
Consumption of single LED (mA)
(panic, disabling ring)
Storage temperature (°C)
Operating temperature (°C)
IP Rating
Video standard
Display colour TFT LCD (pollici)
Terminal board H①
+
Local power supply
–
BUS line input
B
+
Doorbell
–
Alarm Input
AL
Setup of jumpers
Selection of source of power supply (BUS/LOCAL) I
Separate power supply ①
Power supply by BUS ②
Selection of last receiver on the line (CL.RES) J
Master/slave selection (M/S) K
In the event of a call, the caller's picture is displayed only on those receivers
configured as "MASTER"s.
Installation diagrams
Limits and distances with power supply by BUS L
Limits and distances with local power supply M
Locally powered devices ①.
Ringtone Settings
NOTE. See the entry panel documentation for call programming.
Entering Programming.
Press button
A short tone confirms the entry into the programming.
Programming the ring tone associated to a call from the entry
panel (1 acoustic signal).
To listen to the ring tones in sequence press key .
To select the ring tone and exit programming press key
To select the ring tone and continue programming press key
Futura X1
Programming the ring tone associated to a call from the front door
15÷20
(2 acoustic signals).
410
To listen to the ring tones in sequence press key .
<1
To select the ring tone and exit programming press key
16÷18
To select the ring tone and continue programming press key
370
Programming the number of call rings (3 acoustic signals).
1
Press key the same number of times as the rings selected for the call (from
-25 ÷ +70
1 to 6 rings). Three seconds after the last press of the key the call selected for
0 ÷ +35
the chosen number of rings will be played back.
20
To select the ring tone and exit programming completely press key
PAL/NTSC
7
DISPOSAL - Do not litter the environment with packing material: make
sure it is disposed of according to the regulations in force in the country
where the product is used. When the equipment reaches the end of its
life cycle, take measures to ensure it is not discarded in the environment.
The equipment must be disposed of in compliance with the regulations
in force, recycling its component parts wherever possible. Components
that qualify as recyclable waste feature the relevant symbol and the
material's abbreviation.
CE Declaration - BPT S.p.A. a Socio Unico declares that this device
complies with directive 2014/30/UE. Original upon request.
5 times in 5 secs.
.
.
.
.
.
7