Publicidad
Idiomas disponibles
Idiomas disponibles
Speed adjustments
The built-in module permits:
-
Soft start.
-
The maintenance of a practically constant rated speed
up to rated power.
The control electronics allow continuous pre-setting of
the revolutions to adapt the machine to the type of material
to be worked on. Adjustment is made using the speed
adjustment switch C, which has 6 positions to regulate the
speed.
SPECIFICATIONS AND APPLICATIONS OF TABLE 1
Grinding wheel (A)
Abrasive:
Corundum: suitable for steels and steel alloys.
Silicon carbide: cast iron, light metals, hard metal,
building materials.
Hardness:
Soft: hard materials, smooth surfaces, more intense
roughing, fine polishing.
Hard: soft materials, rough, sharp surfaces, less
intense and longer lasting roughing, high quality surface.
Hard Metal Milling Cutter (B)
Rough toothing: stainless steel, steel alloys, light
metals.
Fine toothing: hard steels, hardened steels.
Felt Wheels (C)
These require paste for polishing.
Valve grinding, shiny finishing of ground or polished
surfaces.
Fans (D)
Dies and moulds and light deburring work.
Wire Brush (E)
Steel wire: for cleaning rusty surfaces.
Brass wire: for matt surfaces.
Stainless steel wire: for stainless steel items.
DUST/CHIP ExTRACTION
Dusts from materials such as lead-containing coatings,
some wood types, minerals and metal can be harmful to
one's health. Touching or breathing-in the dusts can cause
allergic reactions and/or lead to respiratory infections of the
user or bystanders.
NOISE AND VIBRATION
This tool has been designed and made to reduce
noise to a minimum. However, in spite of this, in certain
circumstances the maximum noise level in the place of
work could exceed 85 dBA. In this case, the operator
should wear ear protection.
The machine's noise and vibration levels, measured in
compliance with EN60745, usually reach:
Sound pressure level, dB(A)
Sound power level, dB(A)
Uncertainty K, dB(A)
Vibration total values a
, m/s
h
Uncertainty K, m/s
2
Use ear protection!
WARNING! The vibration level given in these
SG6/600CE
85
98
3
2.5
2
1.5
instructions has been measured in accordance with
a standardized measurement procedure specified in
EN60745 and can be used to compare devices. Different
uses of the device give rise to different vibration levels and
in many cases they may exceed the values given in these
instructions. It is easy to underestimate the vibration load
if the electrical power tool is used regularly in particular
circumstances.
Note. If you wish to make an accurate assessment of
the vibration loads experienced during a particular period of
working , you should also take into account the intervening
periods of time when the device is switched off or is running
but is not actually in use. This can result in a much lower
vibration load over the whole of the period of working.
ACCESSORIES
Accessories and their corresponding order number
can be found in our catalogues.
MAINTENANCE AND CARE
WARNING! Always unplug the machine before
carrying out work on it.
WARNING! Type Y attachment. If the supply cord
is damaged, it must be replaced by the manufacturer, its
service agent or similarly qualified persons in order to avoid
a hazard.
-
Inspect the tool: Using a worn deburring or cutting tool
will diminish the efficiency of the work and could damage
the motor.
-
Inspect the mounting screws: Regularly inspect all
the mounting screws and ensure they are firmly tightened.
Should any screw be loose, tighten it immediately. Failure
to do so could put you at serious risk.
-
Motor maintenance: Always take the greatest care
over this and make sure that the motor winding is not
damaged and does not become wet with oil or water.
-
The vents should always be kept clean and free of
obstacles.
-
Clean the machine thoroughly after each use. Blast
the motor regularly with compressed air.
-
Check that the mains lead is in good condition. If it is
not, take it to an Official Service Centre to have it replaced.
-
Brush replacement: The brushes should be replaced
after 150 - 200 hours use or when they are less than 10
mm long. Have this done by an Official Service Centre. We
recommend that at every second change of brushes, you
take the machine to one of our Official Service Centres for
general cleaning and oiling.
Use only FELISATTI accessories and spares. Parts
-
the changing of which is not covered in this instruction
manual, should be replaced in a FELISATTI Official
Service Centre.
WARRANTY
See general warranty conditions printed on the
attached sheet.
DISPOSAL
WARNING! Do not dispose of electric tools in the
household waste!
In accordance with European Directive 2002/96/EC
relating to old electrical and electronic appliances and
its translation into national law, used electric tools must
be collected separately and recycled in an ecologically
desirable way.
7
Publicidad
