Publicidad
Idiomas disponibles
Idiomas disponibles
Stereo/mono switch
The
stereo/mono
switch
is combined
with
the
volume
control
and
places
both
channels
in parallel.
This
permits
playing
a monaural
record
and
facilitates centering
adjustments
of set-ups. Place the switch
in "MONO"
by
pulling
out
the
stereo/mono
knob
for
listening
to
monaural
recordings;
use
the
"STEREO"
position
for
all dual-channel
phonograph
records
(press
in stereo/mono
switch),
Balance
This control
serves
to adjust
the sound
to
room
geometry.
Turning
the
control
from
its
center
position
increases
the volume of
one
channel
while
reducing
the volume
of
the other,
Centering stereo set-up
Place
the
stereo-mono
switch
in "MONO"
Position,
Adjust
to medium
volume,
Adjust
the
balance
control
so
that,
when
directly
in front of the loudspeakers set-up, the sound
source appears to be exactly
in the center
between
the two speakers. When
the stereo/
mono
knob
is placed
in
"STEREO",
the
system
is correctly set for stereophonic
liste-
ning.
When
playing
monaural
records,
it is also
advisable
to
follow
the
same
principle
to
obtain
the
best
possible
room
arrangement.
Just
as
at
an
actual
concert
performance,
there
are
good
and
not-so-good
seats
for
stereo
listening
(Fig.
2).
Technical specifications
rtridge (pick-up)
The following instructions apply only for moun-
ting additional cartridges.
Fig. 14
1, Release the cartridge holder from the tone-
arm head by pressing the tonearm
lift a short
turn to the rear,
Be ready to catch the holder,
as it will drop right into your hand
2. Using
the
necessary
spacers,
screws
and
nuts
supplied,
mount
the cartridge
into
the
holder,
The
special gauge supplied will help
you
place the cartridge at the geometrically
correct point,
The
novel
snap-on
mounting
of
the
Dual
pick-up
cartridges
on
the
cartridge
holder
eliminates all other forms of mounting,
The
snap-on mounting secures perfect geometrical
alignment of the stylus tip.
Fig. 15
3. Connect each lead on the cartridge holder
to
its
corresponding
pin
on
the
cartridge.
Each
lead is color-coded as shown
in fig. 16
4. Replace the cartridge holder by placing it
against
the
tonearm
head
and
lock
it by
pressing the tonearm
lift forward
left channel (white)
L left ground (blue)
L right ground (green)
right channel (red)
Fig. 16
Any
piezoelectric
pick-up with
a weight
of
1 —
10 gms. and
1/2" mounting centers can
be mounted in any unit,
Minimum tracking force:
2 p
For
information,
please
contact
your dealer,
Balancing the tonearm
The
tonearm
weight.
is
balanced
by
rotating
the
1.
Set
the stylus force dial to zero,
2.
Unlock
the tonearm,
and
lift it off the
rest.
Move
the tonearm
just to the inside of
the
resting
post
and
turn
the tonearm
coun-
terbalance until the tonearm floats
in horizon-
tal position
Turning the weight clockwise raises the to
arm head, turning it counterclock wise
the tonearm.
Fig. 17
The tonearm
is precisely balanced when edge
"A"
of the
tonearm
head and
edge
"B"
of the tonearm
rest are at equal height (Fig.
18) or when the tonearm
returns by itself to
a horizontal
position
after
the
chassis
is
tapped.
Precise
balance
is especially
important
with
cartridges
that
require
a
low
stylus
force,
The
balancing
operation
need be done only
once, unless you
install a different cartridge.
Fig. 18
During
the
balancing
of
the
operating switch
must
be in its neutral pos:
tion,
so
that
the
tonearm
is disengaged
from
the automatic
mechanism,
To be sure, lock
the tonearm
on
the rest post
turntable
platter by hand, clockwise,
until the
operating lever returns to its neutral position
tonearm
the
then rotate the
Setting stylus force
Once
the tonearm
is balanced, set the stylus
force
by turning
the stylus force
dial.
The
force is continuously adjustable form
t
5.5 grams.
The
unit
will
function
pro
with
as
little
as
1.5
gram
stylus
Publicidad
