SafeWaze 019-2011 Manual De Instrucciones

LE Lanyard
Instruction Manual
019-2011, 019-2012, 019-2013, 019-2014,
019-2015, 019-2016, 021-2062
Leading Edge
WARNING
This product is part of a personal fall arrest system. The manufacturer's instructions must be provided
to users of this equipment. The user must follow the manufacturer's instructions for each component
of the system. The user must read and understand these instructions before using this equipment.
Manufacturer's instructions must be followed for proper use and maintenance of this equipment.
Alterations to this product, misuse of this product, or failure to follow instructions may result in serious
injury or death.
IMPORTANT
Questions regarding the use, care, or suitability of this equipment for your application? Contact
Safewaze.
IMPORTANT
Record identification information before using this product. Identification information may be found on
the equipment label. This information should be recorded in the "Inspection Log" located at the back of
this manual.
OSHA 1926 Subpart M, OSHA 1910.66, ANSI Z359.13
This manual is intended to meet the manufacturer's instructions as required by
ANSI Z359 and should be used as part of an employee training program as required
by OSHA.
User Information
Date of First Use:
Serial#:
Trainer:
User:
Do not throw away these instructions!
Read and understand these instructions before using equipment!
INTRODUCTION
Thank you for purchasing the Safewaze LE Lanyard. This manual must be read and understood in its
entirety, and used as part of an employee training program as required by OSHA or any applicable state
agency. This manual and any other instructional material must be available to the user of the equipment.
The user must understand how to safely and effectively use the LE Lanyard, and all fall protection
equipment used in conjuction with the lanyard.
APPLICABLE SAFETY STANDARDS
When used according to instructions, the LE Lanyard meets all applicable ANSI Z359 standards and
OSHA regulations for fall protection. Applicable standards and regulations depend on the type of work
being done, and may include state-specific regulations. Refer to local, state, and federal (OSHA)
requirements for additional information concerning the governing of occupational safety regarding
Personal Fall Arrest Systems (PFAS).
WORKER CLASSIFICATIONS
Understand the definitions of those who work in proximity of or may be
exposed to fall hazards.
Qualified Person: "Qualified" means one who, by possession of a recognized degree, certificate,
or professional standing, or who by extensive knowledge, training, and experience, has successfully
demonstrated his ability to solve or resolve problems relating to the subject matter, the work, or the
project.
2062
Competent Person: "Competent person" means one who is capable of identifying existing and
predictable hazards in the surroundings or working conditions which are unsanitary, hazardous, or
dangerous to employees, and who has authorization to take prompt corrective measures to eliminate
them.
Authorized Person: "Authorized person" means a person approved or assigned by the employer to
perform a specific type of duty or duties or to be at a specific location or locations at the job site.
It is the responsibility of a Qualified or Competent person to supervise the job site and
ensure safety regulations are complied with.
PRODUCT SPECIFIC APPLICATIONS
Purpose: The Safewaze LE Lanyard is designed to be used as part of a Personal Fall Arrest System
(PFAS).
- A competent person shall train users on this equipment in accordance with OSHA
and ANSI.
- Never exceed a free fall distance of 6 ft. A free fall of more than 6 ft could cause
excessive arrest forces that could result in serious injury or death.
- The Safewaze LE Lanyard has a maximum capacity of ANSI 310 lbs
including any tools, clothing, accessories, etc..., OSHA 420 lbs, unless otherwise
rated by Safewaze.
- Structures for attachment of Safewaze LE Lanyard shall support a
minimum 5,000 lbs or be designed with a safety factor of two by a Qualified Person.
- All Safewaze lanyards must IMMEDIATELY be removed from service if subjected
to fall arrest forces.
- Safewaze lanyards shall be inspected by the end user prior to each usage and
by a Competent Person other than the user at least annually. These inspections shall
be documented.
LIMITATIONS
Fall Clearance: There must be sufficient clearance below the anchorage connector to arrest a fall
before the user strikes the ground or an obstruction. When calculating fall clearance, account for a
MINIMUM 2' safety factor, deceleration distance, user height, length of lanyard/SRL, and all other
applicable factors. (See Figure 1)
***Diagram shown is an example
fall clearance calculation ONLY.
(Original Working Length
prior to a fall event with energy
absorber deployment
Deceleration/Elongation
Required
distance (5' Total)
distance
from
Harness Stretch
Anchorage
(19' Total)
Height of harness dorsal
Swing Falls: Prior to installation or use, make considerations for eliminating or minimizing all swing fall
hazards. Swing falls occur when the anchor is not directly above the location where a fall occurs. Always
work as close to in line with the anchor point as possible. Swing falls significantly increase the likelihood
of serious injury or death in the even of a fall. (See Figure 2)
I I
225 Wilshire Ave SW, Concord NC, 28025 Phone: 800-230-0319
FIGURE 1
For all applications: worker weight capacity range
(including all clothing, tools, and equipment) is
ANSI 130-310 lbs., OSHA 420 lbs.
Fall Clearance Diagram - Foot Level Tie-Off
Lanyard Length
(6' Total)
(1' Total)
D-ring from
worker's feet
(5' Total)
Safety factor
(2' Total)
FIGURE 2
A
FALL-ARREST
I I
Fax: 704-262-9051 Email: info@safewaze.com
COMPATIBILITY OF CONNECTORS
Connectors are compatible with connecting elements when they have been designed to work together
in such a way that their sizes and shapes do not cause their gate mechanisms to inadvertently open
regardless of how they become oriented. Connectors (hooks, carabiners, and D-rings) must be
capable of supporting at least 5,000 lbs. (22.2 kN). Connectors must be compatible with the anchorage
or other system components (See Figure 4). Do not use equipment that is not compatible.
Non-compatible connectors may unintentionally disengage (See Figure 3). Connectors must be
compatible in size, shape, and strength. Self-locking snap hooks and carabiners are required by ANSI
Z359 and OSHA guidelines. Contact Safewaze if you have any questions about compatibility
NOTE: SOME SPECIALITY CONNECTORS HAVE ADDITIONAL
REQUIREMENTS. CONTACT Safewaze WITH QUESTIONS.
FIGURE 3 - UNINTENTIONAL DISENGAGEMENT
1 - Non Compliant Part
3 - Gate opens
2 - Gate presses
against
non-compliant
part
Using a connector that is undersized or irregular in shape (1) to connect a snap hook or carabiner could
allow the connector to force open the gate of the snap hook or carabiner. When force is applied, the gate
of the hook or carabiner presses against the non-compliant part (2) and forces open the gate (3). This
allows the snap hook or carabiner to disengage (4) from the connection point.
MAKING CONNECTIONS
Snap hooks and carabiners used with this equipment must be double locking and/or twist lock. Ensure
all connections are compatible in size, shape and strength. Do not use equipment that is not compatible.
Ensure all connectors are fully closed and locked.
Safewaze connectors (snap hooks and carabiners) are designed to be used only as specified in each
product's user's instructions. See figure 4 for examples of inappropriate connections. Do not connect
snap hooks and carabiners:
• To a D-ring to which another connector is attached.
• In a manner that would result in a load on the gate (with the exception of tie back hooks).
• NOTE: Large snap hooks must not be connected to objects which will result in a load on the gate if
the hook twists or rotates. Snap hooks marked with ANSI Z359.12 and are equipped with a 3,600 lb
(16 kN) gate. Check the marking on your snap hook to verify its compatibility.
• In a false engagement, where features that protrude from the snap hook or carabiner catch on the
anchor, and without visual confirmation seems to be fully engaged to the anchor point.
• To each other.
• By wrapping the web lifeline around an anchor and securing to lifeline except as allowed for Tie Back
models.
• To any object which is shaped or sized in a way that the snap hook or carabiner will not close and
lock, or that roll-out could occur.
• In a manner that does not allow the connector to align properly while under load.
FIGURE 4 - INAPPROPRIATE CONNECTIONS
APPLICATIONS
Personal Fall Arrest: The LE Lanyard is designed as an anchor point to support a
maximum of 1 Personal Fall Arrest System (PFAS) when utilized for fall protection
applications. The structure to which the anchor is attached must withstand loads applied
in the directions permitted by the system of at least 5,000 lbs. Maximum
allowable free fall is 6'.
Restraint: The LE Lanyard is authorized for use in Restraint applications. The structure
to which the anchor is attached must withstand loads applied in the directions permitted
by the system of at least 1,000 lbs NO free fall is permitted. Restraint systems may only
be used on surfaces with slopes up to 4 / 12 (vertical / horizontal). For Restraint
applications, the allowable attachment points to harness are Dorsal D-ring, Chest D-ring,
Side D-rings, and Shoulder D-rings.
Rescue/Confined Space: The LE Lanyard is authorized for use in Rescue/Confined
Space applications. Rescue systems are utilized to safely recover a worker from a
confined location or after exposure to a fall. Composition of rescue systems can vary
based upon the type of rescue involved. The structure to which a Beam Anchor is
attached must withstand loads applied in the directions permitted by the system of at
least 3,000 lbs. NO free fall is permitted. For rescue applications, the allowable
attachment points to harness are Dorsal D-ring, Chest D-ring and Shoulder D-rings.
All above referenced applications have a worker weight capacity range of
ANSI 130-310 lbs (including all clothing, tools, and equipment), OSHA 420 lbs.
I
Web: safewaze.com
.
4 - And parts
disengage.