Description; Purpose; Overview; General Power Tool Safety Warnings - GreenWorks CD24B00 Manual Del Operador

EN
1

DESCRIPTION

1.1

PURPOSE

The machine is intended for driving in and loosening
screws and bolts as well as for tightening and loosening
nuts within the respective range of dimension.
1.2

OVERVIEW

Figure 1.
1 Two-speed gear
train ( HI-LO)
2 Torque adjustment
ring
3 Keyless chuck
2 GENERAL POWER TOOL
SAFETY WARNINGS
Read all safety warnings and all instructions. Failure to
follow the warnings and instructions may result in
electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term "power tool" in the warnings refers to your
battery-operated (cordless) power tool.
2.1

WORK AREA SAFETY

• Keep work area clean and well lit.
areas invite accidents.
• Do not operate power tools in explosive
atmospheres, such as in the presence of flammable
liquids, gases or dust.
which may ignite the dust or fumes.
• Keep children and bystanders away while operating
Distractions can cause you to lose
a power tool.
control.
2.2

ELECTRICAL SAFETY

• Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce
risk of electric shock.
• Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
There is an increased risk of electric
refrigerators.
shock if your body is earthed or grounded.
• Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
• Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool. Keep
4 Switch trigger
5 LED work light
6 Reversing button
7 Bit storage
WARNING
Cluttered or dark
Power tools create sparks
English
cord away from heat, oil, sharp edges and moving
parts. Damaged or entangled cords increase the risk
of electric shock.
• When operating a power tool outdoors, use an
extension cord suitable for outdoor use.
cord suitable for outdoor use reduces the risk of
electric shock.
• If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply.
electric shock.
2.3

PERSONAL SAFETY

• Stay alert, watch what you are doing and use
common sense when operating a power tool. Do not
use a power tool while you are tired or under the
influence of drugs, alcohol or medication.
attention while operating power tools may result in
serious personal injury.
• Use personal protection. Always wear eye
Protective products such as dust mask,
protection.
non-skid safety shoes, hard hat or hearing
protection used appropriately will reduce personal
injuries.
• Prevent unintentional starting. Ensure the switch is
in the off position before connecting to power source
and/or battery pack and when picking up or carrying
Carrying power tools with your finger on the
the tool.
switch or energizing power tools that have the
switch on invites accidents.
• Remove any adjusting key or wrench before turning
the power tool on.
a rotating part of the power tool may result in
personal injury.
• Do not over-reach. Keep proper footing and balance
This enables better control of the power
at all times.
tool in unexpected situations.
• Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts.
hair can be caught in moving parts.
• If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used.
can reduce dust related hazards.
2.4

POWER TOOL USE AND CARE

• Do not force the power tool. Use the correct power
tool for your application.
do the job better and safer at the rate for which it
was designed.
• Do not use the power tool if the switch does not turn
Any power tool that cannot be
it on and off.
controlled with the switch is dangerous and must be
repaired.
• Disconnect the plug from the power source and/or
the battery pack from the power tool before making
4
Use of a
Use of an RCD reduces the risk of
A lapse of
A wrench or a key left attached to
Loose clothes, jewellery or long
Use of dust collection
The correct power tool will