Publicidad
Idiomas disponibles
Idiomas disponibles
ENG
GENERAL INFO
Model*
White: AGH0001S (Plug Type E/F), AGH0001S-IT (Plug Type L), AGH0001S-CH (Plug
(
"-A" ending models
Type J), AGH0001S-UK (Plug Type G), AGH0001S-SA (Plug Type M)
are available for all
Black: AGH0002S (Plug Type E/F), AGH0002S-IT (Plug Type L), AGH0002S-CH (Plug Type
specified models)
J), AGH0002S-UK (Plug Type G), AGH0002S-SA (Plug Type M)
Specification
1
Support of Wi-Fi (2.4 GHz, 18.2 dBm (~66 mW)), supply voltage: 230 (180-253) V AC, 50 Hz,
input current: 3.0 A (≤0.01 A in standby mode), nominal power: 700.0 W, (≤2 W in standby
mode), heating area of up to 30 m
sensor, tilt sensor
Casing
IP44 Protection Class, heat-emitting panel (tempered glass), control unit (PC plastic).
Dimensions: 1000×165×417 mm (floor installation), or 1000×62×365 mm (wall mounting)
Functions
2
Climate control, panel temperature control (up to 120 °С), manual and remote control,
current protection, voltage protection and overheating protection, voice assistants, LED
indication of statuses
Scope of supply
Premium Eco Smart Heater, legs (2 pcs.), mounting brackets (2 pcs.), mounting kit, hole
drilling template, Quick Start Guide, Warranty Card
Warranty
3 years (Service life: 3 years)
* Model with "-A" ending is identical to model without such ending, e.g. AGH0001S-A is identical to AGH0001S, etc.
LED INDICATOR STATUSES
Blue
Green
Red
Purple
POWER BUTTON FUNCTIONS
Press and hold the power button:
For less than 3 seconds to turn the heater on or off;
For 4 to 9 seconds to switch the heater to the Wi-Fi pairing mode;
For more than 10 seconds to reset the heater to the factory settings.
COMPONENTS AND ACCESSORIES (See Figure A)
Power button ❶ , control unit ❷ , heat-emitting panel ❸ , mounting brackets ❹ , power cord ❺ , legs for floor
installation ❻ , fastening bolts ❼ , temperature sensor ❽ , hooks with dowels (for wall mounting) ❾ , hole
drilling template ❿.
INSTALLATION AND CONFIGURATION
1. Unpack the heater and place it on a clean, horizontal surface with its heat-emitting panel facing down.
2. Install the heater as follows:
a. Floor installation (See Figure B):
NOTE. Only horizontal installation is possible.
Screw legs ❻ to the back of the heat-emitting panel using fastening bolts ❼ (See Figure B-1);
ATTENTION! Correct orientation of legs must be observed (See Figure B-2)!
Make sure that screws are securely tightened and that legs are correctly oriented relative to the device body.
b. Wall mounting (See Figure C):
NOTE. Horizontal or vertical wall mounting is possible.
Screw mounting brackets ❹ to the rear surface of the heat-emitting panel using fastening bolts ❼
(See Figure C-1);
ATTENTION! Correct orientation of brackets must be observed (See Figure C-2 for horizontal mounting
and C-3 for vertical mounting)!
aeno.com/documents
Blue
Green
Red
Yellow
3
(depends on the room insulation), temperature
2
Reset to factory settings
Indicator is on
Indicator is blinking
Indicator is blinking 3 times
The device is connected to the power source
The device is activated in the mobile app
The device is in the Wi-Fi pairing mode
The maintained room temperature mode is on
The heating mode is on
The heating mode is off
The device is overheated
9
Publicidad
