mundoclima CL20801 Instrucciones De Instalación página 14

AUTOMATIC OPERATION
Switch on the power and the OPER AT ION indica tion lamp on the
display panel of the indoor unit starts flashing, and turns off after
flashes for 6 times.
1. Use the MODE button to select AUTO.
2. Push the TEMP button to set the desired room temperature .
The most comfortable temperature settings are between 21 C
o
to 28 C.
3. Push the ON/OFF button to start the air conditioner. The OPE -
RATION lamp on the display panel of the indoor unit lights. The
FAN SPE ED is automatically set and there are no fan speed
indicators shown on the display panel of the remote controller.
4. Push the ON/OFF button again to stop the unit operation.
NOTE
1. In the AUTO mode, the air conditioner can logically choose
the mode of COOL, FAN and HEAT by sensing the difference
between the actual ambient room temperature and the set
temperature on the remote controller.
2. If the AUTO mode is not comfortable for you, the desired
mode can be selected manually.
COOL/ HEAT (Cooling only model without) and
FA N Operatio n
1. If the AUTO mode is not comfortable, you may manually over-ride
the settings by using COOL, HEAT or FAN modes.
2. Push the TEMP button to set the desired room temperature.
When in COOLING mode, the most comfortable settings are 21 C
or above. When in HEATING mode, the most comfortable
"
settings are 28 C or below.
3. Push the FAN SPEED to select the FAN mode of AUTO, HIGH,
MED or LOW.
4. Push the ON/OFF button, the operation lamp lights and the air
conditioner start to operate as your settings. Push the ON/OFF
button again to stop this unit operation.
NOTE
The FAN mode can not be used to control the temperature.
While in this mode, only steps 1
"
"
! 3 and 4 may be performed.
DRY Oper ation
1. P ush the MODE button to select DRY.
2. P ush the TEMP button to set the desired temperature from
" "
21 C to 28 C.
3. P ush the ON/OFF button, the OPER ATION lamp lights and the
air conditioner starts to operate in DRY mode at LOW fan
speed. Push the ON/OFF button again to stop this unit operation.
NOTE
Due to the difference of the set temperature of the unit and
the actual indoor temperature, the Air Conditioner when in
DRY mode will automatically operate many times without
running the COOL and FAN mode.
TIMER Operatio n
Push TIMER ON button to set the auto- on time and TIMER OFF
button to set the auto-off time.
1. To set th e st artin g ti me.
1.1 Push the TIMER ON button, then the remote controller shows
TIMER ON , the last set time for the starting operation and the
signal "h" will be shown on the DIGITA L DISPLAY area. You
are now ready to reset the time to START the operation.
1.2 Push the TIMER ON button again to set desired unit start
time.
1.3 After setting the TIMER ON ,there will be a one-half second
delay before the remote controller transmits the signal to
the air conditioner. Then, after approximately another 2
seconds, the signal "h" disappears and the set temperature
will re-appear on the digital display.
2. To set th e stoppi ng time.
2.1 Push the TIMER OFF button and the remote controller will
show TIMER OFF, the last set time for the stopping operation
and the signal "h" will be shown on the DIGITAL DISPLAY area.
You are now ready to reset the time of the STOP operation.
2.2 P ush the T IMER OFF button a gain to set the time you want to
stop the operation.
2.3 After setting the TIME R OFF ,there will be a one-half second
delay before the remote controller transmits the signal to
the air conditioner. Then, after approxima tely another 2
seconds, the signal "h" disa ppears and the set temperature
will re-appear on the digital display.
GB