Publicidad
Idiomas disponibles
Idiomas disponibles
DESCRIPTION
Craftsman 13" planer finishes rough-cut lumber to size
and planes soft and hardwoods up to 6" thick and 13"
wide. Wood feeds into two-blade cutterhead by rubber
infeed/outfeed rollers. Sturdy base construction and
four-post design permits smooth feeding and virtually
snipeless planing. Planer comes with enclosed, univer-
sal ball bearing, 2_/2 HP (max. developed) motor with
overload protection. Motor has ON/OFF switch with
removable key to prevent accidental start-up. Unit fea-
tures rollercase lock for uniform thickness, power move-
ment control for rollercase, depth-of-cut gauge for con-
venient set-up, workpiece thickness pre-set gauge with
6 settings for consistent set-up, easy hands-free
replacement of blades for safety and minimized down-
time, built-in dust collector, top mounted rollers for
workpiece return, built-in carrying handles, cord wraps
for portability and folding infeed/outfeed rollers for
smooth operation. Planer takes cuts up to _/_" per pass
at 24 feet per minute. Inch height scale has graduations
in _A6" increments, and metric height scale has gradua-
tions in lmm increments.
MOTOR
Table Size ...........................
13" x 10%"
Blade Width ...............................
13"
Maximum Depth of Cut .....................
3/32"
Cuts Per Minute .........................
16,000
Dust Collection Port .........................
2V2"
Overall Dimensions........
21" H x 26_/2 " W x 35V2"D
Motor ...............
2V2HP (max, dev,), 15A, 120V
Weight .................................
97 Ibs
OPERATION
SAFETY RULES
WARNING:
For your own safety, read all of the
instructions and precautions before operating tool
WARNING:
Operation of any power tool can result in
foreign objects being thrown into eyes which can result
in severe eye damage. Always wear safety goggles
complying with United States ANSI Z87.1 (shown on
package) before commencing power tool operation.
CAUTION: Always observe the following safety pre-
cautions:
•
Know general power tool safety. Make sure all pre-
cautions are understood (see pages 2, 3 and 6).
• Whenever adjusting or replacing any parts on planer,
turn switch OFF and remove plug from power source.
• Make sure all guards are properly attached and
securely fastened.
• Make sure all moving parts are free from interference.
• Always wear eye protection or face shield.
• Make sure blades are aligned and properly attached
to cutterhead.
• Do not plug in planer unless switch is in off position.
After turning switch on, allow planer to come to full
speed before operating.
•
Keep hands clear of all moving parts.
•
Do not force cut. Slowing or stalling will overheat
motor. Allow automatic feed to function properly.
•
Use quality lumber. Blades last longer and cuts are
smoother with good quality wood.
•
Do not plane material shorter than 15", narrower
than 3A",wider than 13" or thinner than '/8".
•
Never make planing cut deeper than 3/,,.
•
Maintain the proper relationships of infeed and out-
feed table surfaces and cutterhead blade path.
•
Do not back the work toward the infeed table.
• Take precautions against kickback. Do not permit any-
one 1ostand or cross in line of cutterhead's rotation.
Kickback or thrown debris will travel in this direction.
• Turn switch off and disconnect power whenever plan-
er is not in use.
•
Replace knives as they become damaged or dull.
•
Keep planer maintained. Follow maintenance instruc-
tions (see pages 9 -11).
OPERATING
CONTROLS
ON/OFF SWITCH
The ON/OFF switch (A) is located on the front of the
planer motor. To turn the planer ON, move the switch to
the up position. To turn the planer OFF, move the switch
to the down position.
Figure 9 - ON/OFF Switch
SWITCH LOCK
Refer to Figure 10, page 7.
The planer can be lockedfrom unauthorized use by
lockingthe switch.To lock the switch:
• Turn the switch to OFF position and disconnect plan-
er from power source.
•
Pull the key (A) out. The switch cannot be turned on
with the key (A) removed.
NOTE: Should the key (A) be removed from the switch
at the ON position,the switch can be turned off but
cannot be turned on.
Publicidad
